HP Pavilion DV9200 screw size
M2 / M2.5 / M3 · 3 to 11 mm long
If you are replacing a screw on HP Pavilion DV9200, the thread is M2, M2.5 and M3 in lengths from 3 to 11 mm.
There are 28 separate fitment records for it, including wireless card (qty 2, Phillips) (M2), hinge (qty 2, Phillips) (M2) and optical drive (qty 2, Phillips) (M2), plus 25 more in the table below.
Head and drive, as the sources state them: Phillips drive.
28 of the 28 records are marked confirmed, drawn from 1 source (tim.id.au).
For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.
HP Pavilion DV9200 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 11 mm | 0.4 mm | not stated | Phillips | Wireless card (qty 2, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Hinge (qty 2, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Optical drive (qty 2, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Wireless card (qty 2, silver, Phillips) | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | Phillips | Hinge (qty 2, Phillips) | Confirmed |
| M2 | 5 mm | 0.4 mm | not stated | Phillips | Hard drive (qty 2, captive, Phillips)captive | Confirmed |
| M2 | 5 mm | 0.4 mm | not stated | Phillips | Memory (qty 2, captive, Phillips)captive | Confirmed |
| M2 | 5 mm | 0.4 mm | not stated | Phillips | Optical drive (qty 6, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | I/O board (silver,black, Phillips)black finish | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Bracket (qty 2, silver, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Card reader (qty 4, silver, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Display (qty 2, silver, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Heat sink (qty 3, captive, silver, Phillips)captive | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Keyboard (qty 3, silver, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Palm rest (qty 5, silver, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Power button (silver, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Speaker (qty 2, black, Phillips)black finish | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | System board (qty 3, silver, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Unspecified (silver, Phillips) | Confirmed |
| M2.5 | 5 mm | 0.45 mm | not stated | Phillips | Wireless card (qty 2, silver, Phillips) | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | Phillips | Fan (qty 4, captive, Phillips)captive | Confirmed |
| M2.5 | 7 mm | 0.45 mm | not stated | Phillips | Keyboard (Phillips) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | Phillips | Display (qty 6, silver, Phillips) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | Phillips | Optical drive (Phillips) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | Phillips | Palm rest (qty 8, silver, Phillips) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | Phillips | System board (qty 3, silver, Phillips) | Confirmed |
| M3 | 3 mm | 0.5 mm | not stated | Phillips | Hard drive (qty 4, Phillips) | Confirmed |
| M3 | 3 mm | 0.5 mm | not stated | Phillips | Unspecified (qty 4, Phillips) | Confirmed |
Fitment records and sources
Wireless card (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hinge (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Optical drive (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Wireless card (qty 2, silver, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hinge (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Hard drive (qty 2, captive, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Memory (qty 2, captive, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Optical drive (qty 6, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
I/O board (silver,black, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Bracket (qty 2, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Card reader (qty 4, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 2, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Heat sink (qty 3, captive, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 3, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 5, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Power button (silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Speaker (qty 2, black, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 3, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Wireless card (qty 2, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Fan (qty 4, captive, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 6, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Optical drive (Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 8, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 3, silver, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 4, Phillips)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Unspecified (qty 4, Phillips)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–11 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
- Power-tool gearcase and clamshell screws are usually thread-forming (marked "ST") even when the parts list gives an M-size — a normal machine screw of the same size may not hold in the plastic boss.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M2 x 5mm Replacement Bottom Case Screws for Dell Inspiron 3535 Laptop 10-Pack
$4.99 -
M2 x 5mm Phillips Wafer Head Screw for Dell G16 7630 Gaming Laptop Repair - Pack of 100 Black
$7.99 -
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with HP Pavilion DV9200, closest length match first.
- HP EliteBook 2540p also M2 × 3 mm
- Lenovo ThinkPad T510i also M2 × 3 mm
- HP 16-f1000 also M2 × 3 mm
- Lenovo ThinkPad L15 Gen 4 also M2 × 3 mm
- Lenovo ideapad 330E-17ICH also M2 × 3 mm
- Lenovo ThinkPad L420 also M2 × 3 mm
- Lenovo IdeaPad P500 also M2 × 3 mm
- Lenovo ideapad 310 Touch-15IKB also M2 × 3 mm
Questions about HP Pavilion DV9200 screws
- What size screw does HP Pavilion DV9200 use?
- M2 × 11 mm for wireless card (qty 2, Phillips); M2 × 3 mm for hinge (qty 2, Phillips); M2 × 3 mm for optical drive (qty 2, Phillips); M2 × 3 mm for wireless card (qty 2, silver, Phillips); M2 × 4 mm for hinge (qty 2, Phillips); M2 × 5 mm for hard drive (qty 2, captive, Phillips); M2 × 5 mm for memory (qty 2, captive, Phillips); M2 × 5 mm for optical drive (qty 6, Phillips); M2.5 × 5 mm for I/O board (silver,black, Phillips); M2.5 × 5 mm for bracket (qty 2, silver, Phillips); M2.5 × 5 mm for card reader (qty 4, silver, Phillips); M2.5 × 5 mm for display (qty 2, silver, Phillips); M2.5 × 5 mm for heat sink (qty 3, captive, silver, Phillips); M2.5 × 5 mm for keyboard (qty 3, silver, Phillips); .
- How long are the screws in HP Pavilion DV9200?
- The records range from 3 to 11 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for HP Pavilion DV9200?
- The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP Pavilion DV9200?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M2 x 5mm, which match lengths in the records above.