HP Pavilion x360 15 screw size

HP Pavilion x360 15 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2–7.6 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP Pavilion x360 15, closest length match first.

• HP 240 G1 also M2 × 3 mm
• Dell Latitude 3400 also M2 × 2 mm
• HP Compaq Evo N620c also M2 × 4 mm
• HP nx7000 also M2 × 3 mm
• Lenovo Flex 3-1535 also M2 × 4 mm
• Lenovo IdeaPad S206 also M2 × 3 mm
• HP 14 14-f2000 (= 14-fq2000) also M2 × 2 mm
• HP Pavilion x360 14 also M2 × 2 mm

Questions about HP Pavilion x360 15 screws

What size screw does HP Pavilion x360 15 use?

M2 × 2 mm for power button (qty 2, Phillips); M2 × 2 mm for touchpad (qty 3, Phillips); M2 × 2.3 mm for touchpad (qty 3, broadhead, Phillips); M2 × 2.8 mm for touchpad (qty 4, Phillips); M2 × 3 mm for I/O board (qty 2, Phillips); M2 × 3 mm for memory (qty 1, Phillips); M2 × 3 mm for SSD (qty 1, Phillips); M2 × 3 mm for system board (qty 4, Phillips); M2 × 3 mm for touchpad (qty 3, Phillips); M2 × 3 mm for wireless card (qty 1, Phillips); M2 × 3.7 mm for wireless card (qty 1, Phillips); M2 × 4 mm for base cover (qty 4, Phillips); M2 × 4 mm for hinge (qty 1, Phillips); M2 × 4 mm for system board (qty 2, Phillips); M2 × 4.6 mm for battery (qty 7, Phillips); M2 × 4.6 mm for power button (qty 1, .

How long are the screws in HP Pavilion x360 15?

The records range from 2 to 7.6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for HP Pavilion x360 15?

The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP Pavilion x360 15?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.