HP ProBook 440 G0 screw size

HP ProBook 440 G0 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: for pan head / shoulder screw screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
5. The records span 2–6 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP ProBook 440 G0, closest length match first.

• Lenovo ThinkPad E15 also M2 × 2 mm
• Dell Inspiron 14 5420 also M2 × 2 mm
• Acer Aspire 4920G also M2 × 3 mm
• Lenovo ThinkPad R50/p also M2 × 3 mm
• Lenovo ThinkPad X200 / X201 screw kit also M2.5 × 4 mm
• HP 250 G6 also M2 × 2 mm
• Dell Inspiron 17 5770 also M2 × 2 mm
• Lenovo Y50-80 also M2 × 2 mm

Questions about HP ProBook 440 G0 screws

What size screw does HP ProBook 440 G0 use?

M2 × 2 mm for card reader (qty 2, broadhead, Phillips); M2 × 2 mm for power button (qty 1, broadhead, Phillips); M2 × 3 mm for optical drive (qty 1, Phillips); M2 × 3 mm for palm rest (qty 2, pan, Phillips); M2 × 3 mm for power button (qty 1, Phillips); M2 × 3 mm for unspecified (qty 2, Phillips); M2.5 × 3 mm for hard drive (qty 4, Phillips); M2.5 × 3 mm for hinge (qty 6, Phillips); M2.5 × 3 mm for wireless card (qty 2, Phillips); M2.5 × 4 mm for I/O board (qty 1, Phillips); M2.5 × 4 mm for battery (qty 2, Phillips); M2.5 × 4 mm for display (qty 2, Phillips); M2.5 × 4 mm for hinge (qty 4, Torx T8); M2.5 × 4 mm for system board (qty 2, Phillips); M2.5 × 6 mm for keyboard (qty 2, Phillips); M2.

How long are the screws in HP ProBook 440 G0?

The records range from 2 to 6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for HP ProBook 440 G0?

The source lists a Phillips and Torx T8 drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP ProBook 440 G0?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 3mm and M2.5 x 3mm, which match lengths in the records above.