HP ProBook 470 G4 screw size

HP ProBook 470 G4 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2.5–7 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP ProBook 470 G4, closest length match first.

• Lenovo ThinkPad P15v Gen 1 also M2 × 3 mm
• Dell Precision 7760 also M2 × 3 mm
• HP OmniBook 7 Aero 13.3 inch Next Gen AI PC 13-bg1xxx also M2 × 3 mm
• Lenovo IdeaPad P400 Touch also M2 × 3 mm
• Lenovo ThinkPad T440s also M2 × 3 mm
• HP 14-cf0000 also M2 × 3 mm
• Lenovo ideapad 500-15ISK also M2 × 3 mm
• Dell Vostro 13 5370 also M2 × 3 mm

Questions about HP ProBook 470 G4 screws

What size screw does HP ProBook 470 G4 use?

M2 × 3 mm for display (qty 4, Phillips); M2 × 3 mm for display bezel (qty 2, Phillips); M2 × 3 mm for hard drive (qty 2, Phillips); M2 × 3 mm for hinge (qty 2, Phillips); M2 × 3 mm for palm rest (qty 4, Phillips); M2 × 3 mm for power button (qty 1, Phillips); M2 × 3 mm for speaker (qty 2, Phillips); M2 × 3 mm for unspecified (qty 1, Phillips); M2 × 4 mm for SSD (qty 1, Phillips); M2 × 4 mm for wireless card (qty 1, Phillips); M2.5 × 2.5 mm for hinge (qty 4, Phillips); M2.5 × 3 mm for optical drive (qty 2, Phillips); M2.5 × 3 mm for touchpad (qty 4, Phillips); M2.5 × 6 mm for I/O board (qty 1, Phillips); M2.5 × 7 mm for fan (qty 1, Phillips); M2.5 × 7 mm for hinge (qty 5, Phillips); M2.5 × 7 .

How long are the screws in HP ProBook 470 G4?

The records range from 2.5 to 7 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for HP ProBook 470 G4?

The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP ProBook 470 G4?

TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M2.5 x 3mm, which match lengths in the records above.