HP ProBook 640 G1 screw size
M2 · 3 mm long
The screws used on HP ProBook 640 G1 are M2, 3 mm long.
There are 4 separate fitment records for it, including display (qty 4, Phillips) (M2), power button (qty 2, Phillips) (M2) and speaker (qty 2, Phillips) (M2), plus 1 more in the table below.
Head and drive, as the sources state them: Phillips drive.
4 of the 4 records are marked confirmed, drawn from 1 source (h10032.www1.hp.com).
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
HP ProBook 640 G1 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Display (qty 4, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Power button (qty 2, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Speaker (qty 2, Phillips) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | Phillips | Unspecified (qty 3, Phillips) | Confirmed |
Fitment records and sources
Display (qty 4, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Power button (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Speaker (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 3, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 3 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with HP ProBook 640 G1, closest length match first.
- Lenovo ThinkPad W550s also M2 × 3 mm
- Acer Aspire 1820PT also M2 × 3 mm
- Acer Aspire 5741 also M2 × 3 mm
- Lenovo ideapad 130S-14IGM also M2 × 3 mm
- Lenovo ideapad 320E-17IKB also M2 × 3 mm
- Acer Aspire 4935G also M2 × 3 mm
- Dell Latitude 3180 also M2 × 3 mm
- Laptop hinge covers & trim panels also M2 × 3 mm
Questions about HP ProBook 640 G1 screws
- What size screw does HP ProBook 640 G1 use?
- M2 × 3 mm for display (qty 4, Phillips); M2 × 3 mm for power button (qty 2, Phillips); M2 × 3 mm for speaker (qty 2, Phillips); M2 × 3 mm for unspecified (qty 3, Phillips).
- How long are the screws in HP ProBook 640 G1?
- The record gives 3 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for HP ProBook 640 G1?
- The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP ProBook 640 G1?
- TechSpareWarehouse (our own store) lists M2 x 3mm, which matches the length in the records above.