HP ProBook 650 G5 screw size

HP ProBook 650 G5 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 1.6–6 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP ProBook 650 G5, closest length match first.

• Lenovo ideapad 320S-15AST also M2 × 2.5 mm
• HP ProBook 6475b also M2 × 3 mm
• Dell G5 15 5500 also M2 × 2 mm
• Dell Precision 7770 also M2 × 2 mm
• HP Fortis 11 G10 also M2 × 2 mm
• Acer Aspire 4330 also M2 × 3 mm
• HP Elite x2 1012 G1 Tablet with Travel Keyboard also M2 × 2 mm
• Lenovo B51-30 also M2 × 2 mm

Questions about HP ProBook 650 G5 screws

What size screw does HP ProBook 650 G5 use?

M2 × 1.6 mm for display (qty 4, Phillips); M2 × 2 mm for power button (qty 1, Phillips); M2 × 2 mm for touchpad (qty 7, Phillips); M2 × 2 mm for wireless card (qty 1, Phillips); M2 × 2.5 mm for card reader (qty 3, Phillips); M2 × 2.5 mm for fan (qty 1, captive, Phillips); M2 × 3 mm for display (qty 1, Phillips); M2 × 3 mm for power button (qty 1, Phillips); M2 × 3 mm for SSD (qty 1, Phillips); M2 × 3 mm for unspecified (qty 2, Phillips); M2 × 3 mm for wireless card (qty 1, Phillips); M2.5 × 2.5 mm for chassis/frame (qty 5, Torx T8); M2.5 × 3 mm for display (qty 3, Phillips); M2.5 × 3 mm for speaker (qty 1, Phillips); M2.5 × 5 mm for hinge (qty 3, Phillips); M2.5 × 6 mm for chassis/frame (qty.

How long are the screws in HP ProBook 650 G5?

The records range from 1.6 to 6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for HP ProBook 650 G5?

The source lists a Phillips and Torx T8 drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP ProBook 650 G5?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.