HP ProBook x360 11 G6 EE screw size
M2 / M2.5 · 2.5 to 9.2 mm long
The screws used on HP ProBook x360 11 G6 EE are M2 and M2.5 in lengths from 2.5 to 9.2 mm.
There are 15 separate fitment records for it, including bracket (qty 3, broadhead, Phillips) (M2), bracket (qty 1, broadhead, Phillips) (M2) and touchpad (qty 4, Phillips) (M2), plus 12 more in the table below.
Head and drive, as the sources state them: Phillips and Torx T8 drives.
15 of the 15 records are marked confirmed, drawn from 1 source (kaas.hpcloud.hp.com).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
HP ProBook x360 11 G6 EE screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 2.5 mm | 0.4 mm | not stated | Phillips | Bracket (qty 3, broadhead, Phillips) | Confirmed |
| M2 | 2.8 mm | 0.4 mm | not stated | Phillips | Bracket (qty 1, broadhead, Phillips) | Confirmed |
| M2 | 2.8 mm | 0.4 mm | not stated | Phillips | Touchpad (qty 4, Phillips) | Confirmed |
| M2 | 3.2 mm | 0.4 mm | not stated | Phillips | Touchpad (qty 6, Phillips) | Confirmed |
| M2 | 3.3 mm | 0.4 mm | not stated | Phillips | Heat sink (qty 4, Phillips) | Confirmed |
| M2 | 4.4 mm | 0.4 mm | not stated | Phillips | I/O board (qty 2, Phillips) | Confirmed |
| M2 | 4.4 mm | 0.4 mm | not stated | Phillips | Wireless card (qty 1, Phillips) | Confirmed |
| M2.5 | 4.4 mm | 0.45 mm | not stated | Phillips | Battery (qty 4, Phillips) | Confirmed |
| M2.5 | 4.4 mm | 0.45 mm | not stated | Phillips | System board (qty 8, Phillips) | Confirmed |
| M2.5 | 4.9 mm | 0.45 mm | not stated | Phillips | Speaker (qty 4, Phillips) | Confirmed |
| M2.5 | 5.2 mm | 0.45 mm | not stated | Torx T8 | Display (qty 7, Torx T8) | Confirmed |
| M2.5 | 5.2 mm | 0.45 mm | not stated | Torx T8 | Keyboard (qty 3, Torx T8) | Confirmed |
| M2.5 | 5.2 mm | 0.45 mm | not stated | Torx T8 | Unspecified (qty 1, Torx T8) | Confirmed |
| M2.5 | 6.8 mm | 0.45 mm | not stated | Phillips | Keyboard (qty 2, Phillips) | Confirmed |
| M2.5 | 9.2 mm | 0.45 mm | not stated | Torx T8 | Keyboard (qty 2, Torx T8) | Confirmed |
Fitment records and sources
Bracket (qty 3, broadhead, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Bracket (qty 1, broadhead, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Touchpad (qty 4, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Touchpad (qty 6, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Heat sink (qty 4, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
I/O board (qty 2, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Wireless card (qty 1, Phillips)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Battery (qty 4, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
System board (qty 8, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Speaker (qty 4, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Display (qty 7, Torx T8)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 3, Torx T8)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 1, Torx T8)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 2, Phillips)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 2, Torx T8)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 2.5–9.2 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 2.5mm Screws for Dell XPS 14 9440 M.2 SSD Drive – 10-Pack Black
$4.99 -
M2 x 2.5mm Screws for ASUS ROG Strix G17 G713 SSD WiFi Touchpad 10-Pack Black
$4.99
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2.5 x 5mm Screws Compatible with Dell XPS 14 9440 Display Assembly 10-Pack
$4.99 -
M2.5 x 5mm Phillips Wafer Head Screw for Action Camera Protective Housing - Pack of 50 Black
$4.79 each · min. 2
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with HP ProBook x360 11 G6 EE, closest length match first.
- Acer Aspire 4920 also M2 × 2.5 mm
- M.2 NVMe 2230-22110 retention screw also M2 × 2.5 mm
- HP Folio 13-2000 also M2 × 2.5 mm
- HP EliteBook 820 G1 also M2 × 2.5 mm
- HP Envy x360 16 inch 2-in-1 also M2 × 2.5 mm
- Lenovo ThinkPad S440 also M2 × 2.5 mm
- Lenovo ThinkPad R61i also M2 × 2.5 mm
- HP EliteBook 820 G2 also M2 × 2.5 mm
Questions about HP ProBook x360 11 G6 EE screws
- What size screw does HP ProBook x360 11 G6 EE use?
- M2 × 2.5 mm for bracket (qty 3, broadhead, Phillips); M2 × 2.8 mm for bracket (qty 1, broadhead, Phillips); M2 × 2.8 mm for touchpad (qty 4, Phillips); M2 × 3.2 mm for touchpad (qty 6, Phillips); M2 × 3.3 mm for heat sink (qty 4, Phillips); M2 × 4.4 mm for I/O board (qty 2, Phillips); M2 × 4.4 mm for wireless card (qty 1, Phillips); M2.5 × 4.4 mm for battery (qty 4, Phillips); M2.5 × 4.4 mm for system board (qty 8, Phillips); M2.5 × 4.9 mm for speaker (qty 4, Phillips); M2.5 × 5.2 mm for display (qty 7, Torx T8); M2.5 × 5.2 mm for keyboard (qty 3, Torx T8); M2.5 × 5.2 mm for unspecified (qty 1, Torx T8); M2.5 × 6.8 mm for keyboard (qty 2, Phillips); M2.5 × 9.2 mm for keyboard (qty 2, Torx T8.
- How long are the screws in HP ProBook x360 11 G6 EE?
- The records range from 2.5 to 9.2 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for HP ProBook x360 11 G6 EE?
- The source lists a Phillips and Torx T8 drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP ProBook x360 11 G6 EE?
- TechSpareWarehouse (our own store) lists M2 x 2.5mm, M2 x 3mm and M2.5 x 5mm, which match lengths in the records above.