HP Stream 11-r0xx screw size

HP Stream 11-r0xx screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2.2–5.7 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP Stream 11-r0xx, closest length match first.

• HP Pavilion 14-av0xx also M2 × 2.2 mm
• HP Pavilion 16 inch PC 16t-af000 also M2 × 2.9 mm
• Lenovo Z510 Touch also M2 × 5.7 mm
• Dell Inspiron 15 3505 also M2 × 2.2 mm
• HP Spectre Pro x360 also M2 × 2.9 mm
• Lenovo V14 Gen 2 also M2 × 2.8 mm
• Lenovo ideapad 530S-14IKB also M2 × 2.2 mm
• Lenovo V14 Gen 3 also M2 × 2.8 mm

Questions about HP Stream 11-r0xx screws

What size screw does HP Stream 11-r0xx use?

M2 × 2.2 mm for display bezel (qty 2, broadhead, Phillips); M2 × 2.2 mm for heat sink (qty 2, broadhead, Phillips); M2 × 2.2 mm for touchpad (qty 3, broadhead, Phillips); M2 × 2.8 mm for power button (qty 2, Phillips); M2 × 2.8 mm for touchpad (qty 4, Phillips); M2 × 2.9 mm for hinge (qty 2, broadhead, Phillips); M2 × 3.3 mm for battery (qty 6, Phillips); M2 × 3.3 mm for display (qty 4, Phillips); M2 × 3.3 mm for speaker (qty 2, Phillips); M2 × 3.3 mm for system board (qty 4, Phillips); M2 × 3.3 mm for unspecified (qty 1, Phillips); M2 × 3.3 mm for wireless card (qty 1, Phillips); M2 × 5.7 mm for keyboard (qty 11, Phillips); M2.5 × 3.2 mm for hinge (qty 4, broadhead, Phillips).

How long are the screws in HP Stream 11-r0xx?

The records range from 2.2 to 5.7 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for HP Stream 11-r0xx?

The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP Stream 11-r0xx?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 3mm and M2.5 x 3mm, which match lengths in the records above.