HP x2 210 G2 Detachable PC - MSG") screw size

HP x2 210 G2 Detachable PC - MSG") screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2–6 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP x2 210 G2 Detachable PC - MSG"), closest length match first.

• HP 540 also M2 × 2 mm
• Lenovo ThinkPad W530 also M2 × 3 mm
• Dell Latitude D505 also M2 × 3 mm
• HP ProBook 440 14 inch G9 also M2 × 2 mm
• Dell Inspiron 15 7590 also M2 × 3 mm
• Dell Inspiron 14 5485 2-in-1 also M2 × 2 mm
• Lenovo V14 Gen 4 i also M2 × 2 mm
• HP EliteBook 640 14 inch G10 also M2 × 2 mm

Questions about HP x2 210 G2 Detachable PC - MSG") screws

What size screw does HP x2 210 G2 Detachable PC - MSG") use?

M2 × 2 mm for I/O board (qty 1, Phillips); M2 × 2 mm for power button (qty 1, Phillips); M2 × 2 mm for speaker (qty 1, Phillips); M2 × 2 mm for system board (qty 1, broadhead, Phillips); M2 × 2 mm for touchpad (qty 3, broadhead, black,silver, Phillips); M2 × 2 mm for unspecified (qty 2, Phillips); M2 × 2.5 mm for display (qty 10, Phillips); M2 × 3 mm for base cover (qty 4, black, Phillips); M2 × 3 mm for hinge (qty 4, Phillips); M2 × 4 mm for base cover (qty 2, silver, Phillips); M2 × 4 mm for hinge (qty 1, Phillips); M2 × 4 mm for unspecified (qty 2, Phillips); M2 × 5 mm for hinge (qty 1, black, Phillips); M2 × 6 mm for hinge (qty 2, black, Phillips); M3 × 3 mm for hard drive (qty 4, Philli.

How long are the screws in HP x2 210 G2 Detachable PC - MSG")?

The records range from 2 to 6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for HP x2 210 G2 Detachable PC - MSG")?

The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP x2 210 G2 Detachable PC - MSG")?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.