HP ZBook Fury 16 G10 screw size

HP ZBook Fury 16 G10 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 1.8–7.6 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M1.6 heads take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP ZBook Fury 16 G10, closest length match first.

• HP EliteBook 830 13 inch G11 also M2 × 2.5 mm
• Sony PCG-SR27 also M2 × 2.5 mm
• HP 16-r1000 (ids 2101566692 also M2 × 2.5 mm
• Dell Vostro 15 3590 also M2 × 3 mm
• Toshiba Satellite A60 also M2 × 3 mm
• Dell Precision 3561 also M2 × 2.5 mm
• Lenovo ideapad 720S-14IKB also M2 × 2.5 mm
• Lenovo ThinkPad S330 also M2 × 3 mm

Questions about HP ZBook Fury 16 G10 screws

What size screw does HP ZBook Fury 16 G10 use?

M1.6 × 1.8 mm for touchpad (qty 8, Phillips); M2 × 1.9 mm for base cover (qty 2, broadhead, Phillips); M2 × 2.3 mm for card reader (qty 3, broadhead, Phillips); M2 × 2.3 mm for power button (qty 1, broadhead, Phillips); M2 × 2.3 mm for system board (qty 1, broadhead, Phillips); M2 × 2.5 mm for SSD (qty 1, broadhead, Phillips); M2 × 3 mm for wireless card (qty 1, Phillips); M2 × 5 mm for wireless card (qty 2, Phillips); M2 × 5.3 mm for base cover (qty 1, Phillips); M2 × 5.3 mm for memory (qty 3, Phillips); M2 × 5.3 mm for speaker (qty 4, Phillips); M2 × 5.3 mm for system board (qty 7, Phillips); M2 × 5.3 mm for unspecified (qty 4, Phillips); M2 × 6 mm for unspecified (qty 1, Phillips); M2 × 7.

How long are the screws in HP ZBook Fury 16 G10?

The records range from 1.8 to 7.6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.6 screw?

0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.

What screwdriver do I need for HP ZBook Fury 16 G10?

The source lists a Phillips drive. Standard M1.6 heads otherwise take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M1.6?

No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP ZBook Fury 16 G10?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.