IDS Imaging uEye SE camera module mounting threads (4x) screw size
M3 · length not stated in the sources
The screws used on IDS Imaging uEye SE camera module mounting threads (4x) are M3. None of the sources we found gives an exact length, so measure the original before you order.
The record covers mechanical drawing labels 4x thread M3.
This entry is marked confirmed and comes from inosaki.com.
M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
IDS Imaging uEye SE camera module mounting threads (4x) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | not stated | 0.5 mm | not stated | not stated | Mechanical drawing labels 4x thread M3 | Confirmed |
Fitment records and sources
Mechanical drawing labels 4x thread M3
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Camera and optics hardware often uses short screws into thin threaded plates, so check engagement before tightening fully.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- Camera tripod and Arca threads are imperial 1/4-20 and 3/8-16, never M3.
- Camera and tripod mounting threads themselves are imperial 1/4in-20 or 3/8in-16 — the metric M2-M4 screws in rig kits are only for the accessory hardware, not the tripod mount.
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with IDS Imaging uEye SE camera module mounting threads (4x), closest length match first.
- ScopeStuff nylon thumbscrew kit also M3
- Basler ace 2 / racer 2 S industrial cameras also M3
- Aimpoint SM-2001/2007 Micro T1/T2 mount also M3
- Leica M-series stereo microscopes (M165/M205) also M3
- Holosun SCS-MOS optic mounting screw (Glock) also M3
- Partizan / Pilotix PT10 V3 FPV frame also M3
- Glock MOS optic-to-plate mounting screw also M3
- Vintage camera / electronics faceplates also M3
Questions about IDS Imaging uEye SE camera module mounting threads (4x) screws
- What size screw does IDS Imaging uEye SE camera module mounting threads (4x) use?
- M3 for mechanical drawing labels 4x thread M3.
- How long are the screws in IDS Imaging uEye SE camera module mounting threads (4x)?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for IDS Imaging uEye SE camera module mounting threads (4x)?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.