Lenovo E41-15 screw size

Lenovo E41-15 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2–6 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Lenovo E41-15, closest length match first.

• Dell Inspiron 14 5410 2-in-1 also M2 × 3 mm
• Dell XPS / Razer Blade bottom cover screw kit also M2 × 3 mm
• Lenovo Chromebook C340-15 also M2 × 3 mm
• Dell Precision 5490 also M2 × 2 mm
• Lenovo V145 also M2.5 × 2.5 mm
• HP 2103369402; both pages checked, same PDF) also M2 × 2 mm
• Dell Inspiron 13 7378 2-in-1 also M2 × 2 mm
• Lenovo ThinkPad L460 also M2 × 3 mm

Questions about Lenovo E41-15 screws

What size screw does Lenovo E41-15 use?

M2 × 2 mm for base cover (qty 2, flat, black); M2 × 3 mm for display (qty 4, flat, black); M2 × 3 mm for fan (qty 3, black, Phillips); M2 × 3 mm for system board (qty 2, flat, black); M2 × 3 mm for wireless card (qty 1, flat, black); M2 × 4 mm for hard drive (qty 3, flat, silver); M2 × 4 mm for speaker (qty 1, flat, silver); M2 × 5 mm for battery (qty 2, flat, silver); M2 × 5 mm for fan (qty 1, silver, Phillips); M2.5 × 2.5 mm for display (qty 6, flat, black); M2.5 × 6 mm for base cover (qty 8, flat, black); M2.5 × 6 mm for display (qty 5, flat, black); M2.5 × 6 mm for keyboard (qty 3, flat, black); M3 × 3 mm for hard drive (qty 4, flat, silver).

How long are the screws in Lenovo E41-15?

The records range from 2 to 6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Lenovo E41-15?

The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Lenovo E41-15?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 3mm and M2 x 4mm, which match lengths in the records above.