Lenovo Flex 3-1570 screw size

Lenovo Flex 3-1570 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2.5–6 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Lenovo Flex 3-1570, closest length match first.

• HP Compaq nc6400 also M2 × 6 mm
• Lenovo IdeaPad U310 also M2 × 2.5 mm
• Lenovo ideapad 320L-17ISK also M2 × 6 mm
• Dell Inspiron 14 3481 also M2 × 2.5 mm
• HP Mini 2102 also M2 × 4 mm
• HP EliteBook Revolve 810 G3 also M2 × 2.5 mm
• Dell Inspiron 13 5301 also M2 × 2.5 mm
• Sony 877 also M2 × 4 mm

Questions about Lenovo Flex 3-1570 screws

What size screw does Lenovo Flex 3-1570 use?

M2 × 2.5 mm for I/O board (qty 1, black, Phillips); M2 × 2.5 mm for battery (qty 2, black, Phillips); M2 × 2.5 mm for hard drive (qty 3, black, Phillips); M2 × 2.5 mm for hinge (qty 8, black, Phillips); M2 × 2.5 mm for system board (qty 2, black, Phillips); M2 × 2.5 mm for touchpad (qty 2, black, Phillips); M2 × 2.5 mm for wireless card (qty 1, black, Phillips); M2 × 4 mm for I/O board (qty 1, black, Phillips); M2 × 4 mm for battery (qty 2, black, Phillips); M2 × 4 mm for display (qty 2, black, Phillips); M2 × 4 mm for hinge (qty 2, black,silver, Phillips); M2 × 4 mm for system board (qty 5, black, Phillips); M2 × 6 mm for base cover (qty 11, black, Phillips); M2.5 × 4 mm for system board (q.

How long are the screws in Lenovo Flex 3-1570?

The records range from 2.5 to 6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Lenovo Flex 3-1570?

The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Lenovo Flex 3-1570?

TechSpareWarehouse (our own store) lists M2 x 2.5mm, M2 x 4mm and M2 x 6mm, which match lengths in the records above.