Lenovo ideapad 130S-11IGM screw size

Lenovo ideapad 130S-11IGM screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 1.8–5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M1.6 heads take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Lenovo ideapad 130S-11IGM, closest length match first.

• Acer TravelMate 7730A also M2 × 3 mm
• HP EliteBook Folio 1040 G3 also M2 × 2 mm
• HP Pavilion TX1000 also M2 × 3 mm
• HP ProBook 445 G7 also M2 × 2 mm
• Acer Aspire 3810TG also M2 × 3 mm
• Dell Chromebook 14 3400 also M2 × 3 mm
• Lenovo V480c also M2 × 2 mm
• HP EliteBook Folio 1040 G2 also M2 × 2 mm

Questions about Lenovo ideapad 130S-11IGM screws

What size screw does Lenovo ideapad 130S-11IGM use?

M1.6 × 1.8 mm for palm rest (qty 6, silver, Phillips); M1.6 × 3.5 mm for wireless card (qty 4, black, Phillips); M2 × 2 mm for I/O board (qty 3, black, Phillips); M2 × 2 mm for battery (qty 11, black, Phillips); M2 × 2 mm for display (qty 8, silver,black, Phillips); M2 × 2 mm for speaker (qty 4, black, Phillips); M2 × 2 mm for SSD (qty 1, black,silver, Phillips); M2 × 2 mm for system board (qty 1, black, Phillips); M2 × 2 mm for wireless card (qty 1, black,silver, Phillips); M2 × 2.5 mm for I/O board (qty 3, silver, Phillips); M2 × 2.5 mm for battery (qty 3, silver,black, Phillips); M2 × 2.5 mm for display (qty 6, black, Phillips); M2 × 2.5 mm for system board (qty 7, silver,black, Phillips).

How long are the screws in Lenovo ideapad 130S-11IGM?

The records range from 1.8 to 5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.6 screw?

0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.

What screwdriver do I need for Lenovo ideapad 130S-11IGM?

The source lists a Phillips and Torx drive. Standard M1.6 heads otherwise take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M1.6?

No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Lenovo ideapad 130S-11IGM?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.