Lenovo M4400s screw size

Lenovo M4400s screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 3–7 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Lenovo M4400s, closest length match first.

• Lenovo YOGA 710-11IKB also M2 × 4 mm
• Dell Inspiron 8600 also M2 × 3 mm
• Dell Inspiron 14 5425 also M2 × 3 mm
• HP nx7400 also M2 × 3 mm
• Dell Vostro 14 3400 also M2 × 3 mm
• Lenovo ThinkPad C14 Gen 1 Chromebook also M2 × 3 mm
• MSI Wi-Fi card also M2 × 3 mm
• Dell Latitude 5280 also M2 × 3 mm

Questions about Lenovo M4400s screws

What size screw does Lenovo M4400s use?

M2 × 3 mm for display (qty 4, flat, black); M2 × 3 mm for hinge (qty 4, flat, black); M2 × 3 mm for power button (qty 1, flat, black); M2 × 3 mm for SSD (qty 2, flat, black); M2 × 3 mm for wireless card (qty 2, flat, black); M2 × 4 mm for display (qty 2, flat, black); M2 × 4 mm for hard drive (qty 2, flat, black); M2 × 4 mm for touchpad (qty 2, flat, black); M2 × 4 mm for unspecified (qty 2, flat, black); M2.5 × 3 mm for card reader (qty 1, flat, black); M2.5 × 3 mm for system board (qty 3, flat, black); M2.5 × 5 mm for base cover (qty 1, flat, black); M2.5 × 5 mm for DC-in (qty 3, flat, black); M2.5 × 5 mm for system board (qty 6, flat, black); M2.5 × 5 mm for unspecified (qty 3, flat, blac.

How long are the screws in Lenovo M4400s?

The records range from 3 to 7 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Lenovo M4400s?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Lenovo M4400s?

TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M2.5 x 3mm, which match lengths in the records above.