Lenovo ThinkPad E485 screw size

Lenovo ThinkPad E485 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: for wafer (thin) head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
5. The records span 1.65–5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Lenovo ThinkPad E485, closest length match first.

• Lenovo Flex15 also M2 × 2.5 mm
• Dell Inspiron 15 5577 Gaming also M2 × 3 mm
• Lenovo IdeaPad S310 also M2 × 2 mm
• HP ProBook 4415s also M2 × 2 mm
• Lenovo ThinkPad E435 also M2 × 2 mm
• Lenovo ThinkPad X30 also M2 × 3 mm
• Dell Inspiron 14 3493 also M2 × 2 mm
• HP EliteBook 835 13 inch G11 also M2 × 2 mm

Questions about Lenovo ThinkPad E485 screws

What size screw does Lenovo ThinkPad E485 use?

M2 × 1.65 mm for keyboard (qty 2, flat, silver); M2 × 2 mm for power button (qty 1, flat, black); M2 × 2.5 mm for bracket (qty 5, flat, silver); M2 × 2.5 mm for display (qty 4, flat, silver); M2 × 2.5 mm for hinge (qty 2, flat, silver); M2 × 2.5 mm for SSD (qty 1, flat, silver); M2 × 2.5 mm for touchpad (qty 4, flat, silver); M2 × 2.5 mm for unspecified (qty 1, flat, silver); M2 × 2.5 mm for wireless card (qty 1, flat, black); M2 × 3 mm for SSD (qty 1, wafer, silver); M2 × 4 mm for battery (qty 2, small-head, black); M2 × 4.5 mm for speaker (qty 4, broadhead, black); M2.5 × 2.5 mm for hinge (qty 6, flat, black); M2.5 × 5 mm for bracket (qty 2, flat, black); M2.5 × 5 mm for display (qty 4, fl.

How long are the screws in Lenovo ThinkPad E485?

The records range from 1.65 to 5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Lenovo ThinkPad E485?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Lenovo ThinkPad E485?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.