Lenovo ThinkPad T14 Gen 7 base cover screw size
M2 · length not stated in the sources
Lenovo ThinkPad T14 Gen 7 base cover takes M2 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: bottom cover screws per the maintenance manual screw table.
This entry is marked confirmed and comes from manualslib.com.
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Lenovo ThinkPad T14 Gen 7 base cover screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | not stated | 0.4 mm | not stated | not stated | bottom cover screws per the maintenance manual screw table | Confirmed |
Fitment records and sources
bottom cover screws per the maintenance manual screw table
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Lenovo ThinkPad T14 Gen 7 base cover, closest length match first.
- HP 15s-fq3000 also M2
- HP 250 G4 also M2
- Lenovo ThinkPad T470p also M2
- Dell Latitude 7030 Rugged Extreme Tablet also M2
- Dell Latitude 3300 also M2
- Lenovo ThinkPad T480 also M2
- Framework Laptop 16 primary M.2 2280 NVMe SSD also M2
- Lenovo U31-70 also M2
Questions about Lenovo ThinkPad T14 Gen 7 base cover screws
- What size screw does Lenovo ThinkPad T14 Gen 7 base cover use?
- M2 for bottom cover screws per the maintenance manual screw table.
- How long are the screws in Lenovo ThinkPad T14 Gen 7 base cover?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Lenovo ThinkPad T14 Gen 7 base cover?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.