Lenovo ThinkPad T14s 2-in-1 Gen 1 screw size

Lenovo ThinkPad T14s 2-in-1 Gen 1 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M1.2 screw measures about 1.2 mm with calipers (usually a hair under). This device also uses M1.6 / M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.25 mm from one thread crest to the next (40 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 1.7–4.5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M1.2 heads take PH000 / JIS 00 for Phillips and T1–T2 for Torx; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.2 is about 5-8 N·cm into metal threads and 3-5 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Lenovo ThinkPad T14s 2-in-1 Gen 1, closest length match first.

• HP OMEN 17.3 inch Gaming 17-ck0000 also M2 × 3 mm
• Dell Inspiron 14 5406 2-in-1 also M2 × 3 mm
• Lenovo ThinkPad SL400c also M2 × 3 mm
• HP Compaq nx8420 also M2 × 3 mm
• Dell Latitude 3310 also M2 × 3 mm
• Dell Inspiron 15 3593 also M2 × 3 mm
• HP Pavilion ze2200 PC Compaq Presario M2200 also M2 × 3 mm
• Lenovo ThinkPad T15p Gen 3 also M2 × 3 mm

Questions about Lenovo ThinkPad T14s 2-in-1 Gen 1 screws

What size screw does Lenovo ThinkPad T14s 2-in-1 Gen 1 use?

M1.2 × 1.7 mm for keyboard (qty 2, flat, black); M1.6 × 2.1 mm for card reader (qty 2, flat, black); M1.6 × 2.1 mm for speaker (qty 2, flat, black); M1.6 × 2.1 mm for touchpad (qty 7, flat, black); M1.6 × 2.6 mm for fan (qty 2, flat, silver); M1.6 × 2.6 mm for speaker (qty 1, flat, silver); M1.6 × 2.6 mm for system board (qty 5, flat, silver); M1.6 × 2.6 mm for wireless card (qty 1, flat, silver); M2 × 3 mm for fan (qty 3, flat, black); M2 × 3 mm for speaker (qty 1, flat, silver,black); M2 × 3 mm for system board (qty 3, flat, black); M2.5 × 2.3 mm for keyboard (qty 6, flat, black); M2.5 × 4.5 mm for keyboard (qty 6, flat, black); M2.5 × 4.5 mm for system board (qty 4, flat, black).

How long are the screws in Lenovo ThinkPad T14s 2-in-1 Gen 1?

The records range from 1.7 to 4.5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.2 screw?

0.25 mm (coarse), which is the standard pitch for M1.2 machine screws. The tap drill is 0.95 mm and the normal clearance hole is 1.4 mm.

What screwdriver do I need for Lenovo ThinkPad T14s 2-in-1 Gen 1?

The sources do not name the drive. For M1.2, Phillips heads normally take PH000 / JIS 00 and Torx heads T1–T2.

Can I use an imperial screw instead of M1.2?

No. Imperial look-alike: #0-80 UNF (1.52 mm) is the closest imperial screw, but it is bigger — not a substitute. Use a true M1.2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Lenovo ThinkPad T14s 2-in-1 Gen 1?

TechSpareWarehouse (our own store) lists M2 x 3mm, which matches the length in the records above.