Mid-size drone frames screw size
M4 · 8 to 16 mm long
Our records put Mid-size drone frames on M4 screws in lengths from 8 to 16 mm.
It is listed for arm-to-frame bolts on larger hobby quads (motors are usually M3).
This entry is marked reported.
For reference, M4 is 4 mm across the threads at 0.7 mm pitch. The imperial size people confuse it with: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Mid-size drone frames screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 8–16 mm | 0.7 mm | not stated | not stated | arm-to-frame bolts on larger hobby quads (motors are usually M3) | Reported |
Fitment records and sources
arm-to-frame bolts on larger hobby quads (motors are usually M3)
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Frame and motor screws must not reach the motor windings; check the length against the motor's mounting depth.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 8–16 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Grounding/earth-stud screws on hazardous-area (ATEX/IECEx) gas detectors are commonly M4 even though the enclosure body uses larger threaded glands — don't extrapolate the earth screw size to the whole unit.
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Drones, RC & Gimbals
1/10 scale RC cars1/8 scale RC car chassis hardware3D-printed FPV stack mounts and spacers5-inch brushless motor to armAirsoft V2 / EHPA gearbox shellsALware Quad Flyer Spider 500 quadcopter kitAntique wall clock pendulum bracketsArcade marquee retainersARRMA Senton (and similar 1/10 vehicles)ARRMA Senton/kingpin-equipped vehiclesAxial Racing crawler/buggy kitsAxial SCX10 III RC crawler chassis
Browse all 144 in Drones, RC & Gimbals →The same screw also fits
Devices whose records share a thread with Mid-size drone frames, closest length match first.
- HP LaserJet family common hardware also M4 × 8–14 mm
- Nerf blaster thumbscrews (large) also M4 × 8–16 mm
- Typewriter carriage brackets also M4 × 8–14 mm
- Sewing machine motor mount also M4 × 10–16 mm
- Berkel 330M Slicer base/transmission fastener also M4 × 8 mm
- European mortise lock faceplates also M4 × 10–16 mm
- GoPro-style action cam mount on FPV frames also M4 × 15–16 mm
- Meccano boxed sets (modern metric era) and compatible parts also M4 × 8–16 mm
Questions about Mid-size drone frames screws
- What size screw does Mid-size drone frames use?
- M4 × 8–16 mm for arm-to-frame bolts on larger hobby quads (motors are usually M3).
- How long are the screws in Mid-size drone frames?
- The records range from 8 to 16 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Mid-size drone frames?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.