What size screw does Netgear Nighthawk AX8 router use?

M3 × 6–10 mm for shield and board mounting screws.

How long are the screws in Netgear Nighthawk AX8 router?

The records range from 6 to 10 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Netgear Nighthawk AX8 router?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Netgear Nighthawk AX8 router?

TechSpareWarehouse (our own store) lists M3 x 6mm, M3 x 8mm and M3 x 10mm, which match lengths in the records above.

Netgear Nighthawk AX8 router screw size

M3 · 6 to 10 mm long

Our records put Netgear Nighthawk AX8 router on M3 screws in lengths from 6 to 10 mm.

The record covers shield and board mounting screws.

This entry is marked reported and comes from ifixit.com.

M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Netgear Nighthawk AX8 router screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	6–10 mm	0.5 mm	not stated	not stated	Shield and board mounting screws	Reported

Fitment records and sources

M36-10mmreported

Shield and board mounting screws

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 6–10 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Electronics, Racks & Enclosures

19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw 19-inch rack network and AV gear 19-inch rack-mount audio/AV equipment 19-inch server racks 19in / 10in server rack cage nut and screw kit 19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)

Browse all 357 in Electronics, Racks & Enclosures →

The same screw also fits

Devices whose records share a thread with Netgear Nighthawk AX8 router, closest length match first.

Portable medical device enclosure also M3 × 6–10 mm
DAS / NAS enclosure chassis also M3 × 6–10 mm
ISO 7380 button head, small assemblies also M3 × 6–10 mm
GCX barcode scanner adapter kit (scanner-to-bracket) also M3 × 8 mm
PCIe slot covers & rear brackets also M3 × 6 mm
Desktop switch rack-ear kits also M3 × 6–8 mm
Verifone M400 payment terminal rear locking bracket access cover also M3 × 8 mm
Keystone stainless hex standoff (P/N 24295) also M3 × 10 mm

Questions about Netgear Nighthawk AX8 router screws

What size screw does Netgear Nighthawk AX8 router use?: M3 × 6–10 mm for shield and board mounting screws.
How long are the screws in Netgear Nighthawk AX8 router?: The records range from 6 to 10 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Netgear Nighthawk AX8 router?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Netgear Nighthawk AX8 router?: TechSpareWarehouse (our own store) lists M3 x 6mm, M3 x 8mm and M3 x 10mm, which match lengths in the records above.

Heads up: shipping delay