How long are the screws in NovelKeys NK65 keyboard plate and case?

The records range from 4 to 6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for NovelKeys NK65 keyboard plate and case?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for NovelKeys NK65 keyboard plate and case?

TechSpareWarehouse (our own store) lists M2 x 4mm, M2 x 5mm and M2 x 6mm, which match lengths in the records above.

NovelKeys NK65 keyboard plate and case screw size

M2 · 4 to 6 mm long

The screws used on NovelKeys NK65 keyboard plate and case are M2 in lengths from 4 to 6 mm.

It is listed for plate-to-standoff and plate-to-case screws are M2 x 6mm.

This entry is marked confirmed and comes from novelkeys-llc.helpscoutdocs.com.

M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.

NovelKeys NK65 keyboard plate and case screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M2	4–6 mm	0.4 mm	not stated	not stated	Plate-to-standoff and plate-to-case screws are M2 x 6mm	Confirmed

Fitment records and sources

M24-6mmconfirmed

Plate-to-standoff and plate-to-case screws are M2 x 6mm

pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6

Source

How to check the screw before you buy

Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 4–6 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M2

The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
M.2 SSD screw length must match the standoff position (2230/2242/2260/2280/22110) or the drive won't clamp.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Laptops & PCs

2.5in drive trays & caddies Acer / MSI laptops Acer 5510/4020 series I/O and misc chassis screws Acer 7520 / 7220 Acer Aspire / Swift bottom cover Acer Aspire / Swift M.2 SSD Acer Aspire 1310 Acer Aspire 1410 Acer Aspire 1420P Acer Aspire 1650 Acer Aspire 1680 Acer Aspire 1690

Browse all 2799 in Laptops & PCs →

The same screw also fits

Devices whose records share a thread with NovelKeys NK65 keyboard plate and case, closest length match first.

Lenovo B50-50 also M2 × 5 mm
Dell Inspiron 15 5598 also M2 × 4 mm
Lenovo ThinkPad A21P also M2 × 5.1 mm
Dell Latitude 5400 also M2 × 5 mm
HP 245 G7 also M2 × 5 mm
Lenovo ideapad 500-14ISK also M2 × 6 mm
Lenovo ThinkPad Edge E220s also M2 × 4 mm
HP EliteBook 840 Aero G8 also M2 × 4 mm

Questions about NovelKeys NK65 keyboard plate and case screws

What size screw does NovelKeys NK65 keyboard plate and case use?: M2 × 4–6 mm for plate-to-standoff and plate-to-case screws are M2 x 6mm.
How long are the screws in NovelKeys NK65 keyboard plate and case?: The records range from 4 to 6 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M2 screw?: 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
What screwdriver do I need for NovelKeys NK65 keyboard plate and case?: The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
Can I use an imperial screw instead of M2?: No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for NovelKeys NK65 keyboard plate and case?: TechSpareWarehouse (our own store) lists M2 x 4mm, M2 x 5mm and M2 x 6mm, which match lengths in the records above.

Heads up: shipping delay