Refrigerator door handle screw size
M4 · 10 to 16 mm long
Our records put Refrigerator door handle on M4 screws in lengths from 10 to 16 mm.
The record covers handle bracket to the fridge or freezer door.
This entry is marked reported and comes from repairclinic.com.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Refrigerator door handle screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10–16 mm | 0.7 mm | not stated | not stated | handle bracket to the fridge or freezer door | Reported |
Fitment records and sources
handle bracket to the fridge or freezer door
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–16 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Refrigerator door handle, closest length match first.
- Rackmount KVM chassis also M4 × 10 mm
- SICK BEF-AP-EPA universal sensor adapter bracket also M4 × 10 mm
- BYD Battery-Box Premium LVS also M4 × 14 mm
- kvmswitchtech CE-6 / Cat5 IP Matrix rackmount KVM switch also M4 × 10 mm
- Crowcon Xgard Bright fixed gas detector (mining/oil & gas field electronics) also M4 × 10–15 mm
- DIN 41612 backplane / rack card retention also M4 × 10–12 mm
- Elo EMV bracket special pan-head screw (Bag G) also M4 × 10 mm
- POM APM-E Series II parking meter mechanism (single-space parking meter) also M4 × 10 mm
Questions about Refrigerator door handle screws
- What size screw does Refrigerator door handle use?
- M4 × 10–16 mm for handle bracket to the fridge or freezer door.
- How long are the screws in Refrigerator door handle?
- The records range from 10 to 16 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Refrigerator door handle?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.