RF Elements Twin Horn antenna bracket screw size
M6 · 16 to 20 mm long
Our records put RF Elements Twin Horn antenna bracket on M6 screws in lengths from 16 to 20 mm.
The record covers kit uses 2x M6 x 20mm and 8x M6 x 16mm DIN 912 socket screws for pole/bracket assembly.
Head and drive, as the source states them: socket cap head.
This entry is marked confirmed and comes from rfelements.com.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
RF Elements Twin Horn antenna bracket screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 16–20 mm | 1 mm | Socket cap | not stated | Kit uses 2x M6 x 20mm and 8x M6 x 16mm DIN 912 socket screws for pole/bracket assembly | Confirmed |
Fitment records and sources
Kit uses 2x M6 x 20mm and 8x M6 x 16mm DIN 912 socket screws for pole/bracket assembly
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for socket cap screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The records span 16–20 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Rack hole threads vary: 10-32 and 12-24 are still common in US racks alongside M6 - check the rail before buying.
- Burton sells two different M6 lengths: M6x16 for Re:Flex on 4x4/3D boards and M6x13 for EST on Channel boards. The 16mm screw can bottom out or dimple a Channel board base.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M6 x 16mm Black Wafer Head Rack Screws for Rittal DK 7094.100 / 7094.110 / 7094.140 19-inch Rack – 20-Pack Replacement
$8.99Choose size -
M6 x 16mm Black Wafer Head Awning & Box Screws for Thule Awning 326 / 327 / 328, Conduit Box 317 & Xpedition 820 / 821 (50333) – 8-Pack Replacement
$6.99Choose size
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with RF Elements Twin Horn antenna bracket, closest length match first.
- FJD 3D Excavator Guidance System (GNSS/IMU hardware) also M6 × 16–20 mm
- Tektronix RM5 rackmount kit (5/6 Series MSO) also M6 × 16 mm
- Weidmueller ZB 35 busbar terminal blocks / DIN-rail busbar system also M6 × 16 mm
- Weidmuller WDU 70/95 and WDU 120/150 terminal blocks also M6 × 16 mm
- cab Applicator A3200 print-and-apply labeling system (packaging line hardware) also M6 × 16 mm
- Yamaha F25 / T25 outboard motor also M6 × 18–20 mm
- Large soundbars & subwoofers also M6 × 16–20 mm
- Power wheelchair drive motor mounts also M6 × 16–20 mm
Questions about RF Elements Twin Horn antenna bracket screws
- What size screw does RF Elements Twin Horn antenna bracket use?
- M6 × 16–20 mm for kit uses 2x M6 x 20mm and 8x M6 x 16mm DIN 912 socket screws for pole/bracket assembly.
- How long are the screws in RF Elements Twin Horn antenna bracket?
- The records range from 16 to 20 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for RF Elements Twin Horn antenna bracket?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.