Samsung service part 6001-002005 screw size
M1.4 · 4 mm long
Samsung service part 6001-002005 takes M1.4 metric screws, 4 mm long.
Where it is used: phillips flat-head bracket screw, official Samsung part.
Head and drive, as the source states them: flat / countersunk head and Phillips drive.
This entry is marked confirmed and comes from fixpart.co.uk.
For reference, M1.4 is 1.4 mm across the threads at 0.3 mm pitch. The imperial size people confuse it with: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Samsung service part 6001-002005 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 4 mm | 0.3 mm | Flat / countersunk | Phillips | Phillips flat-head bracket screw, official Samsung part | Confirmed |
Fitment records and sources
Phillips flat-head bracket screw, official Samsung part
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
- The record states 4 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Phillips drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Electronics, Racks & Enclosures
The same screw also fits
Devices whose records share a thread with Samsung service part 6001-002005, closest length match first.
- Dental handpiece cartridge screws also M1.4 × 4 mm
- Dell Pro Max 16 Premium MA16250 also M1.4 × 4 mm
- Camera lens/body low-profile 'JIS Micro Profile' fastener also M1.4 × 4 mm
- Mitutoyo vernier/dial caliper clamp screw also M1.4 × 4 mm
- Fairphone 3 internal screws also M1.4 × 4 mm
- Behind-the-ear hearing aid shell also M1.4 × 4 mm
- FPV flight-controller / ESC stacks also M1.4 × 4 mm
- Dell Precision 5480 also M1.4 × 4 mm
Questions about Samsung service part 6001-002005 screws
- What size screw does Samsung service part 6001-002005 use?
- M1.4 × 4 mm for phillips flat-head bracket screw, official Samsung part.
- How long are the screws in Samsung service part 6001-002005?
- The record gives 4 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Samsung service part 6001-002005?
- The source lists a Phillips drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.