How long are the screws in Samsung vacuum cleaner?

The records range from 6 to 21 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Samsung vacuum cleaner?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Samsung vacuum cleaner?

TechSpareWarehouse (our own store) lists M3 x 6mm, M3 x 8mm and M3 x 10mm, which match lengths in the records above.

Samsung vacuum cleaner screw size

M3 · 6 to 21 mm long

If you are replacing a screw on Samsung vacuum cleaner, the thread is M3 in lengths from 6 to 21 mm.

It is listed for genuine Samsung vacuum screw listed as 'taptite ph + b M3 L10 cblack swrch' (part 6003-000159); Simplicity vacuum motor screw 'M3 X 21' (A733-0300); Nilfisk vacuum screws 'M3 x 20mm' (VF14244) and 'M3 x 6' (VA14006).

This entry is marked confirmed and comes from fixpart.ie.

An M3 screw is 3 mm in diameter with a 0.5 mm pitch, tapped with a 2.5 mm drill; imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Samsung vacuum cleaner screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	6–21 mm	0.5 mm	not stated	not stated	Genuine Samsung vacuum screw listed as 'taptite ph + b M3 L10 cblack swrch' (part 6003-000159); Simplicity vacuum motor screw 'M3 X 21' (A733-0300); Nilfisk vacuum screws 'M3 x 20mm' (VF14244) and 'M3 x 6' (VA14006)self-tapping / thread-forming, black finish	Confirmed

Fitment records and sources

M3L6-L21mm depending on assemblyconfirmed

Genuine Samsung vacuum screw listed as 'taptite ph + b M3 L10 cblack swrch' (part 6003-000159); Simplicity vacuum motor screw 'M3 X 21' (A733-0300); Nilfisk vacuum screws 'M3 x 20mm' (VF14244) and 'M3 x 6' (VA14006)

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

Appliance panels often use self-tapping screws into sheet metal or plastic, and machine screws into nuts or inserts — keep each type where it came from.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 6–21 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

On FPV motors, screw length is safety-critical: one turn too long and the screw crushes the motor windings. Measure arm + base depth, and dry-fit before powering up.
Cleanroom/vacuum-rated M3 screws (titanium, vented, low-outgas) from NBK are a distinct specialty class, priced and sourced very differently from commodity M3 hardware — do not substitute one for the other in semiconductor fixtures.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Appliances & HVAC

Appliance door hinges Appliance handles Astoria/CMA espresso solenoid group head (used in coffee kiosk equipment)Astoria/CMA espresso solenoid group head screw Berkel 330M Slicer cover fastener Berkel 330M Slicer sharpener/guard mounting Bezzera Giulia espresso machine Bosch dishwasher Coffee machine control panel Daikin FTXS/CTXS Mini-split control board / cover screw Daikin FTXS/CTXS Mini-split indoor unit mounting / terminal cover screw Daikin FTXS/CTXS Mini-split indoor unit terminal cover / mounting plate screw

Browse all 62 in Appliances & HVAC →

The same screw also fits

Devices whose records share a thread with Samsung vacuum cleaner, closest length match first.

Daikin FTXS/CTXS Mini-split control board / cover screw also M3 × 20 mm
Coffee machine control panel also M3 × 6–10 mm
Vulcan-Hart Chef combi oven also M3 × 12 mm
OE Lido / Fixie hand coffee grinder also M3 × 6 mm
Microwave door latch and hinge also M3 × 6–10 mm
Dyson filter cap and battery cover also M3 × 6–10 mm
Lenovo ThinkPad 765D also M3 × 6 mm
HP Compaq Presario C300 also M3 × 6 mm

Questions about Samsung vacuum cleaner screws

What size screw does Samsung vacuum cleaner use?: M3 × 6–21 mm for genuine Samsung vacuum screw listed as 'taptite ph + b M3 L10 cblack swrch' (part 6003-000159); Simplicity vacuum motor screw 'M3 X 21' (A733-0300); Nilfisk vacuum screws 'M3 x 20mm' (VF14244) and 'M3 x 6' (VA14006).
How long are the screws in Samsung vacuum cleaner?: The records range from 6 to 21 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Samsung vacuum cleaner?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Samsung vacuum cleaner?: TechSpareWarehouse (our own store) lists M3 x 6mm, M3 x 8mm and M3 x 10mm, which match lengths in the records above.

Heads up: shipping delay