Sony SR27K screw size
M2 / M3 · 2.5 to 6 mm long
The screws used on Sony SR27K are M2 and M3 in lengths from 2.5 to 6 mm.
There are 4 separate fitment records for it, including unspecified (qty 2, flat, silver) (M2), unspecified (qty 1, gold) (M2) and unspecified (qty 4, silver) (M2), plus 1 more in the table below.
4 of the 4 records are marked confirmed, drawn from 1 source (tim.id.au).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Sony SR27K screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 2.5 mm | 0.4 mm | not stated | not stated | Unspecified (qty 2, flat, silver) | Confirmed |
| M2 | 3.5 mm | 0.4 mm | not stated | not stated | Unspecified (qty 1, gold) | Confirmed |
| M2 | 6 mm | 0.4 mm | not stated | not stated | Unspecified (qty 4, silver) | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Unspecified (qty 94) | Confirmed |
Fitment records and sources
Unspecified (qty 2, flat, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 1, gold)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 4, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 94)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 2.5–6 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M3
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
- M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 2.5mm Screws for Dell XPS 14 9440 M.2 SSD Drive – 10-Pack Black
$4.99 -
M2 x 2.5mm Screws for ASUS ROG Strix G17 G713 SSD WiFi Touchpad 10-Pack Black
$4.99
-
M2 x 6mm Phillips Wafer Head Screw for HP Omen Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2 x 6mm Phillips Wafer Head Screw for Audiophile Headphone Headband Repair - Pack of 50 Black
$4.99
-
M3 x 4mm Phillips Wafer Head Screws for 2.5 SATA SSD Mounting 10-Pack
$4.99 -
M3 x 4mm Screws for Installing SSD into Synology NAS 10-Pack
$4.99 -
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Sony SR27K, closest length match first.
- Lenovo ThinkPad P14s Gen 1 also M2 × 2.5 mm
- Lenovo IP 5 Chrome 16IAU7 also M2 × 2.5 mm
- Lenovo Flex 4-1570 also M2 × 3.5 mm
- Dell Inspiron 13 7300 2-in-1 also M2 × 3.5 mm
- Lenovo V330-14ARR also M2 × 2.5 mm
- Lenovo G505 also M2 × 6 mm
- HP 256 G3 also M2 × 3.5 mm
- Acer Aspire 5530G also M2 × 6 mm
Questions about Sony SR27K screws
- What size screw does Sony SR27K use?
- M2 × 2.5 mm for unspecified (qty 2, flat, silver); M2 × 3.5 mm for unspecified (qty 1, gold); M2 × 6 mm for unspecified (qty 4, silver); M3 × 4 mm for unspecified (qty 94).
- How long are the screws in Sony SR27K?
- The records range from 2.5 to 6 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Sony SR27K?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Sony SR27K?
- TechSpareWarehouse (our own store) lists M2 x 2.5mm, M2 x 6mm and M3 x 4mm, which match lengths in the records above.