Tilta TA-RF-LPL adapter ring support (RED KOMODO cage) screw size
M4 · 8 to 12.5 mm long
Tilta TA-RF-LPL adapter ring support (RED KOMODO cage) takes M4 metric screws in lengths from 8 to 12.5 mm.
The record covers M4x8 secures the LPL adapter; M4x12.5 mounts it to the camera cage.
This entry is marked confirmed and comes from manualspro.net.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Tilta TA-RF-LPL adapter ring support (RED KOMODO cage) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 8–12.5 mm | 0.7 mm | not stated | not stated | M4x8 secures the LPL adapter; M4x12.5 mounts it to the camera cage | Confirmed |
Fitment records and sources
M4x8 secures the LPL adapter; M4x12.5 mounts it to the camera cage
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Do not confuse metric mounting screws with the 1/4-20 or 3/8-16 tripod threads that cameras and clamps also carry.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 8–12.5 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
- Camera rig/cage accessories (SmallRig, Wooden Camera/Metabones) frequently mix M4 structural screws with 1/4-20 and 3/8-16 imperial mounting points on the same product — verify which specific fastener a manual is referencing before ordering replacements.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M4 x 10mm Black Wafer Head Charging Port Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 10-Pack Replacement
$5.49Choose size -
M4 x 10mm Black Wafer Head Fender Clamp Base Screws for Minoura KODACHI DYK-1R Rear Fender – 8-Pack Replacement
$5.49Choose size -
M4 x 12mm Black Wafer Head Chainsaw & Cut-off Saw Screws for STIHL MS 460, MS 362, TS480i & TS500i (IS-M4x12) – 10-Pack Replacement
$5.49Choose size -
M4 x 12mm Black Wafer Head Monitor VESA, Neck & Stand Screws for Dell UltraSharp U4320Q & Sceptre Monitors – 8-Pack Replacement
$5.49Choose size
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Tilta TA-RF-LPL adapter ring support (RED KOMODO cage), closest length match first.
- Underwater camera housing latch and port also M4 × 8–12.5 mm
- Wooden Camera UMB-1 Universal Mattebox (Base/Clamp On/Swing Away/Pro) also M4 × 8–12.5 mm
- ATC (Advanced Transportation Controller) traffic signal cabinet standard also M4 × 10 mm
- Sig Sauer ROMEO1 Pro mounting screw also M4 × 8.5 mm
- Holosun 507k/407k screw, Glock 43X/48 MOS shim plate also M4 × 12 mm
- Celestron NexStar 8 eyepiece holder set screw also M4 × 12 mm
- NEMA TS-2 traffic signal control cabinet (roadside traffic controller cabinet) also M4 × 12 mm
- Riflescope ring cap also M4 × 10–12.5 mm
Questions about Tilta TA-RF-LPL adapter ring support (RED KOMODO cage) screws
- What size screw does Tilta TA-RF-LPL adapter ring support (RED KOMODO cage) use?
- M4 × 8–12.5 mm for M4x8 secures the LPL adapter; M4x12.5 mounts it to the camera cage.
- How long are the screws in Tilta TA-RF-LPL adapter ring support (RED KOMODO cage)?
- The records range from 8 to 12.5 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Tilta TA-RF-LPL adapter ring support (RED KOMODO cage)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.