Toshiba Satellite 2400 screw size

Toshiba Satellite 2400 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2.6–16 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Toshiba Satellite 2400, closest length match first.

• Lenovo ideapad 510-15IKB also M2 × 3 mm
• Lenovo ThinkPad S431 also M2 × 3 mm
• HP ZBook 8 G1ak 14 (ZBook 8 G1a family; G1ah also M2 × 4 mm
• Lenovo ThinkPad S31 also M2 × 4 mm
• Lenovo V110-15ISK also M2 × 3 mm
• HP EliteBook 8440w also M2 × 3 mm
• Lenovo ThinkPad T14s Gen 6 Snapdragon also M2 × 5 mm
• HP 250R G9 / 256R G9 also M2 × 4 mm

Questions about Toshiba Satellite 2400 screws

What size screw does Toshiba Satellite 2400 use?

M2 × 12 mm for card reader (qty 4); M2 × 3 mm for display (qty 4, flat); M2 × 3 mm for optical drive (qty 1, flat, silver); M2 × 4 mm for display (qty 4); M2 × 4 mm for hard drive (qty 4, flat, silver); M2 × 4 mm for memory (qty 2, flat); M2 × 4 mm for unspecified (qty 1, flat); M2 × 5 mm for hard drive (qty 2, flat, silver); M2 × 5 mm for optical drive (qty 2, flat, silver); M2 × 5 mm for touchpad (qty 1, flat, silver); M2 × 6 mm for heat sink (qty 2); M2 × 6 mm for palm rest (qty 1); M2 × 6 mm for unspecified (qty 2); M2.5 × 14 mm for system board (qty 1); M2.5 × 16 mm for palm rest (qty 2, black); M2.5 × 16 mm for unspecified (qty 2, black); M2.5 × 2.6 mm for keyboard (qty 2, flat, black).

How long are the screws in Toshiba Satellite 2400?

The records range from 2.6 to 16 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Toshiba Satellite 2400?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Toshiba Satellite 2400?

TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M2 x 5mm, which match lengths in the records above.