Toshiba Tecra 9000 screw size
M2 / M2.5 / M3 · 2.8 to 16 mm long
Our records put Toshiba Tecra 9000 on M2, M2.5 and M3 screws in lengths from 2.8 to 16 mm.
There are 25 separate fitment records for it, including palm rest (qty 4, flat, black) (M2), palm rest (qty 4, silver) (M2) and display (qty 4, silver) (M2), plus 22 more in the table below.
Head and drive, as the sources state them: Torx drive.
25 of the 25 records are marked confirmed, drawn from 1 source (xdevs.com).
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Toshiba Tecra 9000 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 10 mm | 0.4 mm | not stated | not stated | Palm rest (qty 4, flat, black)black finish | Confirmed |
| M2 | 12 mm | 0.4 mm | not stated | not stated | Palm rest (qty 4, silver) | Confirmed |
| M2 | 2.8 mm | 0.4 mm | not stated | not stated | Display (qty 4, silver) | Confirmed |
| M2 | 2.8 mm | 0.4 mm | not stated | not stated | Speaker (qty 4, silver) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Unspecified (qty 5, silver) | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | not stated | Keyboard (qty 2) | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | Torx | Wireless card (qty 1, black, Torx)black finish | Confirmed |
| M2 | 8 mm | 0.4 mm | not stated | not stated | Unspecified (qty 2, silver) | Confirmed |
| M2.5 | 14 mm | 0.45 mm | not stated | not stated | Keyboard (qty 1, flat, black)black finish | Confirmed |
| M2.5 | 14 mm | 0.45 mm | not stated | not stated | Palm rest (black)black finish | Confirmed |
| M2.5 | 16 mm | 0.45 mm | not stated | not stated | Palm rest (qty 6, silver) | Confirmed |
| M2.5 | 16 mm | 0.45 mm | not stated | not stated | Unspecified (qty 1) | Confirmed |
| M2.5 | 16 mm | 0.45 mm | not stated | not stated | Wireless card (qty 1, silver) | Confirmed |
| M2.5 | 2.8 mm | 0.45 mm | not stated | not stated | Keyboard (qty 2, silver) | Confirmed |
| M2.5 | 2.8 mm | 0.45 mm | not stated | not stated | Memory (qty 2, flat, silver) | Confirmed |
| M2.5 | 2.8 mm | 0.45 mm | not stated | not stated | Palm rest (qty 2, flat, silver) | Confirmed |
| M2.5 | 3 mm | 0.45 mm | not stated | not stated | Unspecified (qty 3, flat, silver) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Palm rest (qty 2, flat, black)black finish | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Speaker (qty 4) | Confirmed |
| M2.5 | 4 mm | 0.45 mm | not stated | not stated | Unspecified (qty 5) | Confirmed |
| M2.5 | 6 mm | 0.45 mm | not stated | not stated | Speaker (qty 2, flat) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Hard drive (qty 1, silver) | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Keyboard (qty 2, flat, black)black finish | Confirmed |
| M2.5 | 8 mm | 0.45 mm | not stated | not stated | Palm rest (qty 4, black)black finish | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Wireless card (qty 4, flat) | Confirmed |
Fitment records and sources
Palm rest (qty 4, flat, black)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Palm rest (qty 4, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Display (qty 4, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Speaker (qty 4, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 5, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Keyboard (qty 2)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Wireless card (qty 1, black, Torx)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (qty 2, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Keyboard (qty 1, flat, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 6, silver)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 1)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Wireless card (qty 1, silver)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 2, silver)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Memory (qty 2, flat, silver)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 2, flat, silver)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 3, flat, silver)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 2, flat, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Speaker (qty 4)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Unspecified (qty 5)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Speaker (qty 2, flat)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Hard drive (qty 1, silver)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Keyboard (qty 2, flat, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Palm rest (qty 4, black)
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Wireless card (qty 4, flat)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5 / M3, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 2.8–16 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Torx drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M2.5 / M3
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
- 3.5in desktop and enterprise hard drives are 6-32 UNC imperial, not M3 - only the 2.5in form factor is metric.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M2 x 8mm Phillips Wafer Head Screw for Dell XPS 15 9560 Laptop Repair - Pack of 100 Black
$7.99 -
10x M2 x 8mm Phillips Screws for HP Fortis 14 G11 Chromebook Bottom Cover
$4.99 -
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Toshiba Tecra 9000, closest length match first.
- Acer TravelMate 8531 also M2 × 4 mm
- Dell Inspiron 14 5480 also M2 × 3 mm
- Dell Latitude 9420 2-in-1 also M2 × 4 mm
- HP Pavilion ze4900 also M2 × 3 mm
- Dell XPS 13 9340 also M2 × 3 mm
- HP Pavilion x360 14 inch 2-in-1 also M2 × 3 mm
- HP 620 also M2 × 3 mm
- HP Compaq Presario C700 also M2 × 3 mm
Questions about Toshiba Tecra 9000 screws
- What size screw does Toshiba Tecra 9000 use?
- M2 × 10 mm for palm rest (qty 4, flat, black); M2 × 12 mm for palm rest (qty 4, silver); M2 × 2.8 mm for display (qty 4, silver); M2 × 2.8 mm for speaker (qty 4, silver); M2 × 3 mm for unspecified (qty 5, silver); M2 × 4 mm for keyboard (qty 2); M2 × 4 mm for wireless card (qty 1, black, Torx); M2 × 8 mm for unspecified (qty 2, silver); M2.5 × 14 mm for keyboard (qty 1, flat, black); M2.5 × 14 mm for palm rest (black); M2.5 × 16 mm for palm rest (qty 6, silver); M2.5 × 16 mm for unspecified (qty 1); M2.5 × 16 mm for wireless card (qty 1, silver); M2.5 × 2.8 mm for keyboard (qty 2, silver); M2.5 × 2.8 mm for memory (qty 2, flat, silver); M2.5 × 2.8 mm for palm rest (qty 2, flat, silver); M2.5.
- How long are the screws in Toshiba Tecra 9000?
- The records range from 2.8 to 16 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Toshiba Tecra 9000?
- The source lists a Torx drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Toshiba Tecra 9000?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M2 x 8mm, which match lengths in the records above.