Ubiquiti UniFi AP / UAP-LR ceiling & wall mount kit screw size
M3 · 50 mm long
Our records put Ubiquiti UniFi AP / UAP-LR ceiling & wall mount kit on M3 screws, 50 mm long.
Where it is used: three flat head screws with three keps nuts secure the mounting bracket.
Head and drive, as the source states them: flat / countersunk head.
This entry is marked confirmed and comes from dl.ubnt.com.
For reference, M3 is 3 mm across the threads at 0.5 mm pitch. The imperial size people confuse it with: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Ubiquiti UniFi AP / UAP-LR ceiling & wall mount kit screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | 50 mm | 0.5 mm | Flat / countersunk | not stated | Three flat head screws with three keps nuts secure the mounting bracket | Confirmed |
Fitment records and sources
Three flat head screws with three keps nuts secure the mounting bracket
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
- The record states 50 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- 2020 extrusion T-nuts come in M3/M4/M5 and are not interchangeable — M3 is accessory-only, M5 is structural.
- LED wall cabinets use different threads at different points - M3 on bezels, M4 on frame links and tops, M6 on frame joints. 'An M4 for the LED wall' is not enough information.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Ubiquiti UniFi AP / UAP-LR ceiling & wall mount kit, closest length match first.
- Ubiquiti UniFi UAP-AC access point also M3 × 50 mm
- Wurth Elektronik WA-SSTIE steel spacer stud also M3 × 50 mm
- Ubiquiti UniFi AP-AC-LITE access point also M3 × 50 mm
- Wurth Elektronik WA-SPAIE plastic spacer stud also M3 × 50 mm
- Ubiquiti UniFi AP-PRO access point also M3 × 50 mm
- Ubiquiti UniFi AP-AC-PRO access point also M3 × 50 mm
- Ubiquiti UniFi AP ceiling mount also M3 × 50 mm
- Ubiquiti UniFi UAP / UAP-LR access point also M3 × 50 mm
Questions about Ubiquiti UniFi AP / UAP-LR ceiling & wall mount kit screws
- What size screw does Ubiquiti UniFi AP / UAP-LR ceiling & wall mount kit use?
- M3 × 50 mm for three flat head screws with three keps nuts secure the mounting bracket.
- How long are the screws in Ubiquiti UniFi AP / UAP-LR ceiling & wall mount kit?
- The record gives 50 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Ubiquiti UniFi AP / UAP-LR ceiling & wall mount kit?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.