What size screw does Acer Nitro / Predator Wi-Fi card use?

M2 × 3 mm for WLAN card screw on the gaming models.

How long are the screws in Acer Nitro / Predator Wi-Fi card?

The record gives 3 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Acer Nitro / Predator Wi-Fi card?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Acer Nitro / Predator Wi-Fi card?

TechSpareWarehouse (our own store) lists M2 x 3mm, which matches the length in the records above.

Acer Nitro / Predator Wi-Fi card screw size

M2 · 3 mm long

Our records put Acer Nitro / Predator Wi-Fi card on M2 screws, 3 mm long.

It is listed for WLAN card screw on the gaming models.

This entry is marked reported and comes from acer.com.

For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.

Acer Nitro / Predator Wi-Fi card screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M2	3 mm	0.4 mm	not stated	not stated	WLAN card screw on the gaming models	Reported

Fitment records and sources

M2~3mmreported

WLAN card screw on the gaming models

pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6

Source

How to check the screw before you buy

A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The record states 3 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M2

M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Laptops & PCs

2.5in drive trays & caddies Acer / MSI laptops Acer 5510/4020 series I/O and misc chassis screws Acer 7520 / 7220 Acer Aspire / Swift bottom cover Acer Aspire / Swift M.2 SSD Acer Aspire 1310 Acer Aspire 1410 Acer Aspire 1420P Acer Aspire 1650 Acer Aspire 1680 Acer Aspire 1690

Browse all 2799 in Laptops & PCs →

The same screw also fits

Devices whose records share a thread with Acer Nitro / Predator Wi-Fi card, closest length match first.

Lenovo ThinkPad T450 laptop also M2 × 3 mm
Dell Vostro 15 5510 also M2 × 3 mm
Lenovo ideapad 320-15IKB Touch also M2 × 3 mm
Lenovo ThinkPad L560 also M2 × 3 mm
Dell Inspiron 14 5418 also M2 × 3 mm
Dell Inspiron 14 5402 also M2 × 3 mm
Lenovo S40 also M2 × 3 mm
Dell Inspiron 14 5498 also M2 × 3 mm

Questions about Acer Nitro / Predator Wi-Fi card screws

What size screw does Acer Nitro / Predator Wi-Fi card use?: M2 × 3 mm for WLAN card screw on the gaming models.
How long are the screws in Acer Nitro / Predator Wi-Fi card?: The record gives 3 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M2 screw?: 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
What screwdriver do I need for Acer Nitro / Predator Wi-Fi card?: The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
Can I use an imperial screw instead of M2?: No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Acer Nitro / Predator Wi-Fi card?: TechSpareWarehouse (our own store) lists M2 x 3mm, which matches the length in the records above.

Heads up: shipping delay