Audient EVO 16 audio interface rack kit screw size
M4 · length not stated in the sources
If you are replacing a screw on Audient EVO 16 audio interface rack kit, the thread is M4. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: rack ear kit ships with M4 screws for 1U mounting.
This entry is marked confirmed and comes from wrdtunes.com.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Audient EVO 16 audio interface rack kit screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | not stated | 0.7 mm | not stated | not stated | Rack ear kit ships with M4 screws for 1U mounting | Confirmed |
Fitment records and sources
Rack ear kit ships with M4 screws for 1U mounting
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Board standoffs and enclosure bosses set the usable length: the screw should clamp the board without bottoming in the standoff.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Some rackmount KVM switch kits pair M4x10 bracket-to-rack screws with M3.2x4.5 bracket-to-chassis screws (non-standard M3.2, not a true M3), so kits are not fully interchangeable with generic M3/M4 hardware.
- Festo sensor brackets are named after the sensor interface (DASP-M4-...), but the bracket's own fixing screws are often a different size (M5/M6/M8).
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Audient EVO 16 audio interface rack kit, closest length match first.
- Tesla Universal Wall Connector (48A single phase) also M4
- Weidmueller BFSC busbar/DIN-rail screw accessory also M4
- SICK BEF-SEC100 sensingCam mounting bracket also M4
- Electrolux Professional compact rack-type dishwasher also M4
- Supermicro SSE-F3548S / F3548SR switch also M4
- ETC Unison DRd Rack Enclosure (dimming rack for theatrical rigging systems) also M4
- Ubiquiti UniFi rack ear kit screws (UACC-Rack-Ear, 1U/2U) also M4
- SICK sensingCam SEC200/400 L-bracket kit also M4
Questions about Audient EVO 16 audio interface rack kit screws
- What size screw does Audient EVO 16 audio interface rack kit use?
- M4 for rack ear kit ships with M4 screws for 1U mounting.
- How long are the screws in Audient EVO 16 audio interface rack kit?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Audient EVO 16 audio interface rack kit?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.