Banner Engineering PVL sensor (SMBPVL4 bracket) screw size
M6 · length not stated in the sources
Our records put Banner Engineering PVL sensor (SMBPVL4 bracket) on M6 screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for "PVL sensors mount to the bracket using M6 hardware" — drawing shows M6 x 1.
This entry is marked confirmed and comes from info.bannerengineering.com.
For reference, M6 is 6 mm across the threads at 1 mm pitch. The imperial size people confuse it with: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Banner Engineering PVL sensor (SMBPVL4 bracket) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | not stated | 1 mm | not stated | not stated | "PVL sensors mount to the bracket using M6 hardware" — drawing shows M6 x 1 | Confirmed |
Fitment records and sources
"PVL sensors mount to the bracket using M6 hardware" — drawing shows M6 x 1
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Cymbal stand top threads (M6) are a separate standard from tension rod/lug threads (M5) on the same drum kit, so hardware is not interchangeable between the two locations.
- 19-inch racks are not all metric: 10-32 and 12-24 UNC are still the norm in North America, with M6 the metric/square-hole cage-nut option.
More in Electronics, Racks & Enclosures
The same screw also fits
Devices whose records share a thread with Banner Engineering PVL sensor (SMBPVL4 bracket), closest length match first.
- StarTech CABSCRWM620 rack kit also M6
- Power-One 15kW/25kW wind interface also M6
- 48280AH lithium battery pack enclosure wheels also M6
- Wurth Elektronik WA-SSTIE steel spacer stud also M6
- 19-inch rack cage nut and panel screw also M6
- Xiaomi M365 / Ninebot brake caliper also M6
- Thule Bike Racks (General Replacement) also M6
- Hammond CAGKIT rack mounting kit also M6
Questions about Banner Engineering PVL sensor (SMBPVL4 bracket) screws
- What size screw does Banner Engineering PVL sensor (SMBPVL4 bracket) use?
- M6 for "PVL sensors mount to the bracket using M6 hardware" — drawing shows M6 x 1.
- How long are the screws in Banner Engineering PVL sensor (SMBPVL4 bracket)?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Banner Engineering PVL sensor (SMBPVL4 bracket)?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.