Basler dart M screw kit (order no. 2200002092) screw size
M2 · length not stated in the sources
Our records put Basler dart M screw kit (order no. 2200002092) on M2 screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for 4x M2 hex nuts for lens mount attachment.
This entry is marked confirmed and comes from resources.ampheo.com.
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Basler dart M screw kit (order no. 2200002092) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | not stated | 0.4 mm | not stated | not stated | 4x M2 hex nuts for lens mount attachment | Confirmed |
Fitment records and sources
4x M2 hex nuts for lens mount attachment
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Do not confuse metric mounting screws with the 1/4-20 or 3/8-16 tripod threads that cameras and clamps also carry.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Basler dart M screw kit (order no. 2200002092), closest length match first.
- Olympus BH-2 / BH2-5RE microscope nosepiece also M2
- Basler ace Classic/U USB 3.0 also M2
- Some Nikkor lens mounts also M2
- DJI O3 Air Unit camera module also M2
- Ophthalmic instrument service hardware (Duclos Lenses) also M2
- Olympus BH-2 / MIC-D microscope frame also M2
- Basler dart M industrial camera mount kit also M2
- DJI Mavic Pro gimbal/camera mounting screws also M2
Questions about Basler dart M screw kit (order no. 2200002092) screws
- What size screw does Basler dart M screw kit (order no. 2200002092) use?
- M2 for 4x M2 hex nuts for lens mount attachment.
- How long are the screws in Basler dart M screw kit (order no. 2200002092)?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Basler dart M screw kit (order no. 2200002092)?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.