How long are the screws in Camper/caravan/tent fitting screw?

The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Camper/caravan/tent fitting screw?

The source lists a Pozidriv drive. Standard M3 heads otherwise take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Camper/caravan/tent fitting screw?

TechSpareWarehouse (our own store) lists M3 x 6mm, which matches the length in the records above.

Camper/caravan/tent fitting screw screw size

M3 · 6 mm long

Camper/caravan/tent fitting screw takes M3 metric screws, 6 mm long.

Where it is used: camperlands sells a 'Pozi Countersunk Screw M3 X 6MM' listed among caravan/tent hardware accessories.

Head and drive, as the source states them: flat / countersunk head and Pozidriv drive.

This entry is marked reported and comes from camperlands.co.uk.

M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Camper/caravan/tent fitting screw screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	6 mm	0.5 mm	Flat / countersunk	Pozidriv	Camperlands sells a 'Pozi Countersunk Screw M3 X 6MM' listed among caravan/tent hardware accessories	Reported

Fitment records and sources

M36mmreported

Camperlands sells a 'Pozi Countersunk Screw M3 X 6MM' listed among caravan/tent hardware accessories

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

Where the manufacturer publishes a torque value, use a torque driver rather than feel.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
The record states 6 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source names a Pozidriv drive. For comparison, standard M3 heads take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

Thor Zone Nanoq S case mixes metric M3 (various lengths: 4, 5, 6, 10, 13, 20mm) and imperial #6-32 UNC fasteners across the same build, so builders must sort hardware carefully rather than assuming an all-metric kit.
ISO 14581 Torx countersunk screws look like plain countersunk screws but need the right lobe driver; a Phillips bit will chew the head.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Vehicles, Marine & Mobility

ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insert Adult e-scooters Aftermarket car stereo cage Airgun scope/rail mount replacement screws Alpine Head Units Analogis phono cartridge screw set Arduino UNO / full-size Arduino boards Audio MusiKraft cartridge mounting screw kit Audio MusiKraft cartridge/headshell mounting kit Bar-end plug or bar-end shifter Berkel 330M Slicer carriage/guard fastener

Browse all 171 in Vehicles, Marine & Mobility →

The same screw also fits

Devices whose records share a thread with Camper/caravan/tent fitting screw, closest length match first.

Fishing reel side plate / frame also M3 × 6 mm
OE Handgrinders Fixie coffee grinder also M3 × 6 mm
Gotrax electric scooter assembly screw also M3 × 6 mm
Fishing reel handle retainer also M3 × 6 mm
Dell U2412M also M3 × 6 mm
Olympus BH-2 microscope frame also M3 × 6 mm
HP V24ie G5 also M3 × 6 mm
Dell UZ2215H also M3 × 6 mm

Questions about Camper/caravan/tent fitting screw screws

What size screw does Camper/caravan/tent fitting screw use?: M3 × 6 mm for camperlands sells a 'Pozi Countersunk Screw M3 X 6MM' listed among caravan/tent hardware accessories.
How long are the screws in Camper/caravan/tent fitting screw?: The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Camper/caravan/tent fitting screw?: The source lists a Pozidriv drive. Standard M3 heads otherwise take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Camper/caravan/tent fitting screw?: TechSpareWarehouse (our own store) lists M3 x 6mm, which matches the length in the records above.

Heads up: shipping delay