Dell Latitude 7520 screw size

Dell Latitude 7520 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 1.7–5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M1.6 heads take PH00 for Phillips and T4–T5 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Dell Latitude 7520, closest length match first.

• LG LW60 also M2 × 3 mm
• Lenovo ideapad 320-14AST also M2 × 3 mm
• Acer TravelMate 5220 also M2 × 3 mm
• Lenovo ThinkPad E550c also M2 × 3 mm
• Lenovo ThinkPad Z61p also M2 × 3 mm
• Acer TravelMate 2480 also M2 × 3 mm
• Lenovo ThinkPad X201s also M2 × 2 mm
• Lenovo ThinkPad E475 also M2 × 3 mm

Questions about Dell Latitude 7520 screws

What size screw does Dell Latitude 7520 use?

M1.6 × 1.7 mm for keyboard (qty 20); M1.6 × 1.7 mm for power button (qty 2); M2 × 2 mm for display (qty 2); M2 × 2 mm for keyboard (qty 2); M2 × 2 mm for palm rest (qty 3); M2 × 2 mm for SSD (qty 2); M2 × 2 mm for system board (qty 3); M2 × 2 mm for unspecified (qty 2); M2 × 2 mm for wireless card (qty 1); M2 × 2.5 mm for I/O board (qty 2); M2 × 2.5 mm for card reader (qty 4); M2 × 2.5 mm for chassis/frame (qty 4); M2 × 2.5 mm for heat sink (qty 6); M2 × 2.5 mm for speaker (qty 2); M2 × 2.5 mm for system board (qty 5); M2 × 2.5 mm for unspecified (qty 1); M2 × 2.5 mm for wireless card (qty 1); M2 × 3 mm for system board (qty 2); M2 × 4 mm for I/O board (qty 2); M2 × 4 mm for system board (qt.

How long are the screws in Dell Latitude 7520?

The records range from 1.7 to 5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.6 screw?

0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.

What screwdriver do I need for Dell Latitude 7520?

The sources do not name the drive. For M1.6, Phillips heads normally take PH00 and Torx heads T4–T5; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M1.6?

No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell Latitude 7520?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.