Diebold Nixdorf DN100 nylon screw screw size
M4 · 5 to 6 mm long
Our records put Diebold Nixdorf DN100 nylon screw on M4 screws in lengths from 5 to 6 mm.
The record covers M4 slotted nylon screw, ~5-6mm, listed as a DN100 ATM spare.
Head and drive, as the source states them: Slotted drive.
This entry is marked reported.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Diebold Nixdorf DN100 nylon screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 5–6 mm | 0.7 mm | not stated | Slotted | M4 slotted nylon screw, ~5-6mm, listed as a DN100 ATM sparethread-locking patch | Reported |
Fitment records and sources
M4 slotted nylon screw, ~5-6mm, listed as a DN100 ATM spare
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Check whether the mount uses a VESA pattern or a vendor bracket before buying screws.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 5–6 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Slotted drive. For comparison, standard M4 heads take PH2 (Phillips) or T20 (Torx), or a 3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Printers, POS & Office
Arca-Swiss / GoPro DIY adaptersBixolon SRP-B300II POS receipt printerBrother DCP-8110D laser printerBrother HL-2170W laser printerBrother MFC-8950DW laser printerCoin validator / hopper front plateCoin-door / vending coin mech holder thumb screwCOSEL power supply terminal blockDiebold Nixdorf ATM (PN 49221808000F-26)Diebold Nixdorf DN100 ATMDiebold Opteva ATM cassette screwElo countertop self-service stand screw
Browse all 58 in Printers, POS & Office →The same screw also fits
Devices whose records share a thread with Diebold Nixdorf DN100 nylon screw, closest length match first.
- NCR S2 dispenser module screw also M4 × 5 mm
- Diebold Opteva ATM cassette screw also M4 × 5–6 mm
- Elo E458992 EMV PIN Pad Mounting Kit also M4 × 6 mm
- Heidelberg offset press (OEM parts 00.500.0177 / 00.540.1025) also M4 × 6 mm
- Elo self-service kiosk stand screw (Bag L) also M4 × 6 mm
- Heidelberg offset press (OEM part 00.520.1346) also M4 × 5 mm
- Datalogic DS2400 fixed-mount barcode reader also M4 × 5 mm
- Singer 3323/3321 sewing machine also M4 × 6 mm
Questions about Diebold Nixdorf DN100 nylon screw screws
- What size screw does Diebold Nixdorf DN100 nylon screw use?
- M4 × 5–6 mm for M4 slotted nylon screw, ~5-6mm, listed as a DN100 ATM spare.
- How long are the screws in Diebold Nixdorf DN100 nylon screw?
- The records range from 5 to 6 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Diebold Nixdorf DN100 nylon screw?
- The source lists a Slotted drive. Standard M4 heads otherwise take PH2 (Phillips) or T20 (Torx), or a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.