Heidelberg offset press (OEM part 00.520.1346) screw size
M4 · 5 mm long
If you are replacing a screw on Heidelberg offset press (OEM part 00.520.1346), the thread is M4, 5 mm long.
The record covers DIN 933 hex head screw M4 x 5mm.
This entry is marked confirmed and comes from shop.printersparts.com.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Heidelberg offset press (OEM part 00.520.1346) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 5 mm | 0.7 mm | not stated | not stated | DIN 933 hex head screw M4 x 5mm | Confirmed |
Fitment records and sources
DIN 933 hex head screw M4 x 5mm
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Printers and POS terminals often use self-tapping screws into plastic; re-use the original thread path instead of cutting a new one.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 5 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Printers, POS & Office
Arca-Swiss / GoPro DIY adaptersBixolon SRP-B300II POS receipt printerBrother DCP-8110D laser printerBrother HL-2170W laser printerBrother MFC-8950DW laser printerCoin validator / hopper front plateCoin-door / vending coin mech holder thumb screwCOSEL power supply terminal blockDiebold Nixdorf ATM (PN 49221808000F-26)Diebold Nixdorf DN100 ATMDiebold Nixdorf DN100 nylon screwDiebold Opteva ATM cassette screw
Browse all 58 in Printers, POS & Office →The same screw also fits
Devices whose records share a thread with Heidelberg offset press (OEM part 00.520.1346), closest length match first.
- NCR S2 dispenser module screw also M4 × 5 mm
- Diebold Opteva ATM cassette screw also M4 × 5 mm
- Diebold Nixdorf DN100 nylon screw also M4 × 5 mm
- Takara Belmont PRO III 047 dental chair also M4 × 5 mm
- DIN 912 socket-head cap screw also M4 × 5 mm
- DIN 965 / ISO 7046 countersunk Phillips screw also M4 × 5 mm
- Cognex In-Sight 9000 machine vision system also M4 × 5 mm
- Wurth Elektronik WA-SSTIE steel spacer stud also M4 × 5 mm
Questions about Heidelberg offset press (OEM part 00.520.1346) screws
- What size screw does Heidelberg offset press (OEM part 00.520.1346) use?
- M4 × 5 mm for DIN 933 hex head screw M4 x 5mm.
- How long are the screws in Heidelberg offset press (OEM part 00.520.1346)?
- The record gives 5 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Heidelberg offset press (OEM part 00.520.1346)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.