DJI OEM mounting screw (quad/hex arm hardware) screw size
M2.5 · 5 to 7 mm long
Our records put DJI OEM mounting screw (quad/hex arm hardware) on M2.5 screws in lengths from 5 to 7 mm.
It is listed for arm and motor mount screw sold as OEM DJI part.
This entry is marked confirmed and comes from modelemax.pl.
An M2.5 screw is 2.5 mm in diameter with a 0.45 mm pitch, tapped with a 2.05 mm drill; imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.
DJI OEM mounting screw (quad/hex arm hardware) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2.5 | 5–7 mm | 0.45 mm | not stated | not stated | Arm and motor mount screw sold as OEM DJI part | Confirmed |
Fitment records and sources
Arm and motor mount screw sold as OEM DJI part
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- Frame and motor screws must not reach the motor windings; check the length against the motor's mounting depth.
- Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 5–7 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2.5
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2.5 x 5mm Screws Compatible with Dell XPS 14 9440 Display Assembly 10-Pack
$4.99 -
M2.5 x 5mm Phillips Wafer Head Screw for Action Camera Protective Housing - Pack of 50 Black
$4.79 each · min. 2
-
M2.5 x 6mm Laptop Motherboard Replacement Screws Wafer Head 10-Pack Black
$4.99 -
10x M2.5 x 6mm Phillips Screws for Lenovo ThinkPad X131e Chromebook LCD Hinge
$4.99
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
Dell Inspiron 15 3520 Replacement Screws Sold Individually – M2 x 3mm, M2 x 5mm, M2.5 x 5mm, M3 x 3mm Phillips Wafer Head, Black
$0.10Choose size -
Dell Latitude 5430 Replacement Screws Sold Individually – M2 x 2.5mm, M2 x 3mm, M2 x 5mm, M2.5 x 5mm Phillips Wafer Head, Black
$0.10Choose size
More in Drones, RC & Gimbals
1/10 scale RC cars1/8 scale RC car chassis hardware3D-printed FPV stack mounts and spacers5-inch brushless motor to armAirsoft V2 / EHPA gearbox shellsALware Quad Flyer Spider 500 quadcopter kitAntique wall clock pendulum bracketsArcade marquee retainersARRMA Senton (and similar 1/10 vehicles)ARRMA Senton/kingpin-equipped vehiclesAxial Racing crawler/buggy kitsAxial SCX10 III RC crawler chassis
Browse all 144 in Drones, RC & Gimbals →The same screw also fits
Devices whose records share a thread with DJI OEM mounting screw (quad/hex arm hardware), closest length match first.
- Axial SCX10 III RC crawler, countersunk and cap screws also M2.5 × 5–7 mm
- Antique wall clock pendulum brackets also M2.5 × 5–7 mm
- Holybro X500 V2 with Pixhawk 6C (PX4 official build) also M2.5 × 6 mm
- PowerVision PowerRay underwater drone also M2.5 × 6–7 mm
- Sewing machine needle plate also M2.5 × 5–7 mm
- Raspberry Pi (Model B+ through Pi 4/Pi 5 form factor boards) also M2.5 × 6–7 mm
- Drone remote controller internals also M2.5 × 5–7 mm
- Model aircraft control horns also M2.5 × 6–7 mm
Questions about DJI OEM mounting screw (quad/hex arm hardware) screws
- What size screw does DJI OEM mounting screw (quad/hex arm hardware) use?
- M2.5 × 5–7 mm for arm and motor mount screw sold as OEM DJI part.
- How long are the screws in DJI OEM mounting screw (quad/hex arm hardware)?
- The records range from 5 to 7 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2.5 screw?
- 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
- What screwdriver do I need for DJI OEM mounting screw (quad/hex arm hardware)?
- The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
- Can I use an imperial screw instead of M2.5?
- No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for DJI OEM mounting screw (quad/hex arm hardware)?
- TechSpareWarehouse (our own store) lists M2.5 x 5mm and M2.5 x 6mm, which match lengths in the records above.