What size screw does Drone remote controller internals use?

M2.5 × 5–10 mm for board and case assembly screws.

How long are the screws in Drone remote controller internals?

The records range from 5 to 10 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2.5 screw?

0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.

What screwdriver do I need for Drone remote controller internals?

The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.

Can I use an imperial screw instead of M2.5?

No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Drone remote controller internals?

TechSpareWarehouse (our own store) lists M2.5 x 5mm, M2.5 x 6mm and M2.5 x 8mm, which match lengths in the records above.

Drone remote controller internals screw size

M2.5 · 5 to 10 mm long

If you are replacing a screw on Drone remote controller internals, the thread is M2.5 in lengths from 5 to 10 mm.

The record covers board and case assembly screws.

This entry is marked reported and comes from ifixit.com.

For reference, M2.5 is 2.5 mm across the threads at 0.45 mm pitch. The imperial size people confuse it with: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.

Drone remote controller internals screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M2.5	5–10 mm	0.45 mm	not stated	not stated	Board and case assembly screws	Reported

Fitment records and sources

M2.55-10mmreported

Board and case assembly screws

pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8

Source

How to check the screw before you buy

Vibration loosens small screws on drones and RC models, so builders commonly add a drop of medium (blue) threadlocker on metal-to-metal joints — never on plastic.
Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 5–10 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M2.5

M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Drones, RC & Gimbals

1/10 scale RC cars 1/8 scale RC car chassis hardware 3D-printed FPV stack mounts and spacers 5-inch brushless motor to arm Airsoft V2 / EHPA gearbox shells ALware Quad Flyer Spider 500 quadcopter kit Antique wall clock pendulum brackets Arcade marquee retainers ARRMA Senton (and similar 1/10 vehicles)ARRMA Senton/kingpin-equipped vehicles Axial Racing crawler/buggy kits Axial SCX10 III RC crawler chassis

Browse all 144 in Drones, RC & Gimbals →

The same screw also fits

Devices whose records share a thread with Drone remote controller internals, closest length match first.

Model aircraft control horns also M2.5 × 6–8 mm
Raspberry Pi (Model B+ through Pi 4/Pi 5 form factor boards) also M2.5 × 6–10 mm
E-flite Gee Bee R-2 aileron servo cover also M2.5 × 10 mm
Holybro X500 V2 with Pixhawk 6C also M2.5 × 6 mm
Antique wall clock pendulum brackets also M2.5 × 5–10 mm
Holybro X500 V2 with Pixhawk 6C (PX4 official build) also M2.5 × 6 mm
DJI OEM mounting screw (quad/hex arm hardware) also M2.5 × 5–7 mm
Axial SCX10 III RC crawler, countersunk and cap screws also M2.5 × 5–10 mm

Questions about Drone remote controller internals screws

What size screw does Drone remote controller internals use?: M2.5 × 5–10 mm for board and case assembly screws.
How long are the screws in Drone remote controller internals?: The records range from 5 to 10 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M2.5 screw?: 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
What screwdriver do I need for Drone remote controller internals?: The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
Can I use an imperial screw instead of M2.5?: No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Drone remote controller internals?: TechSpareWarehouse (our own store) lists M2.5 x 5mm, M2.5 x 6mm and M2.5 x 8mm, which match lengths in the records above.

Heads up: shipping delay