EcoFlow Power Kits Power Hub wall/RV mounting hardware screw size
M4 / M5 · 10 to 20 mm long
Our records put EcoFlow Power Kits Power Hub wall/RV mounting hardware on M4 and M5 screws in lengths from 10 to 20 mm.
There are 2 separate fitment records for it, including quick start guide lists M4*10 screws included for mounting the Power Hub enclosure (M4) and quick start guide lists M5*10 and M5*20 mounting screws for the Power Hub bracket (M5).
2 of the 2 records are marked confirmed, drawn from 2 sources (carbatterymarket.co.uk and websiteoss.ecoflow.com).
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
EcoFlow Power Kits Power Hub wall/RV mounting hardware screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10 mm | 0.7 mm | not stated | not stated | Quick start guide lists M4*10 screws included for mounting the Power Hub enclosure | Confirmed |
| M5 | 10–20 mm | 0.8 mm | not stated | not stated | Quick start guide lists M5*10 and M5*20 mounting screws for the Power Hub bracket | Confirmed |
Fitment records and sources
Quick start guide lists M4*10 screws included for mounting the Power Hub enclosure
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
Quick start guide lists M5*10 and M5*20 mounting screws for the Power Hub bracket
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). This device also uses M5, so measure each screw rather than assuming they match.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–20 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4 / M5
- Grounding/earth-stud screws on hazardous-area (ATEX/IECEx) gas detectors are commonly M4 even though the enclosure body uses larger threaded glands — don't extrapolate the earth screw size to the whole unit.
- Display mounts mix systems: the screen side is metric M4/M6, but the wall side of many mounts uses imperial wood screws such as #14 x 2.5in.
- Archery sight and rest hardware is almost always imperial 10-24, not metric.
- Espresso/coffee-equipment M5 and M6 socket-head screws (DIN 7984/UNI 9327) are cross-brand standard fasteners shared across CMA, Astoria, and La Cimbali brewing-group hardware, so a single screw often services multiple manufacturers' machines.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M4 x 10mm Black Wafer Head Charging Port Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 10-Pack Replacement
$5.49Choose size -
M4 x 10mm Black Wafer Head Fender Clamp Base Screws for Minoura KODACHI DYK-1R Rear Fender – 8-Pack Replacement
$5.49Choose size -
M5 x 12mm Black Wafer Head Cut-off Saw Screws for STIHL TS400 Cut-off Saw (replaces IS-M5x12 9022 341 0960) – 10-Pack Replacement
$5.99Choose size -
M5 x 12mm Black Wafer Head Generator Cover Screws for Honda EM, EB, EG Generators & EU3200i (replaces 90102-Z21-000) – 10-Pack Replacement
$5.99Choose size
More in Electronics, Racks & Enclosures
The same screw also fits
Devices whose records share a thread with EcoFlow Power Kits Power Hub wall/RV mounting hardware, closest length match first.
- E-scooter fenders & kickstands also M5 × 10–20 mm
- Bicycle bottle cage bosses (Trek and industry standard) also M5 × 10–15 mm
- cab Applicator A3200 print-and-apply labeling system (packaging line hardware) also M4 × 10 mm
- Icom IC-M502 / IC-M501EURO VHF marine radio also M5 × 20 mm
- Wheelchair armrest and footrest brackets also M5 × 12–20 mm
- FJD 3D Excavator Guidance System (GNSS/IMU hardware) also M5 × 12 mm
- Tektronix RM5 rackmount kit (5/6 Series MSO) also M5 × 16 mm
- SMA Sunny Boy 3.0-US to 7.7-US inverter also M5 × 16 mm
Questions about EcoFlow Power Kits Power Hub wall/RV mounting hardware screws
- What size screw does EcoFlow Power Kits Power Hub wall/RV mounting hardware use?
- M4 × 10 mm for quick start guide lists M4*10 screws included for mounting the Power Hub enclosure; M5 × 10–20 mm for quick start guide lists M5*10 and M5*20 mounting screws for the Power Hub bracket.
- How long are the screws in EcoFlow Power Kits Power Hub wall/RV mounting hardware?
- The records range from 10 to 20 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for EcoFlow Power Kits Power Hub wall/RV mounting hardware?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.