Icom IC-M502 / IC-M501EURO VHF marine radio screw size
M5 · 20 mm long
Our records put Icom IC-M502 / IC-M501EURO VHF marine radio on M5 screws, 20 mm long.
Where it is used: mounting bracket uses the 2 supplied M5 x 20mm screws.
This entry is marked confirmed and comes from manualsdump.com.
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Icom IC-M502 / IC-M501EURO VHF marine radio screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 20 mm | 0.8 mm | not stated | not stated | Mounting bracket uses the 2 supplied M5 x 20mm screws | Confirmed |
Fitment records and sources
Mounting bracket uses the 2 supplied M5 x 20mm screws
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 20 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Stacking frame + rack tab + fender stay needs 18-20mm bolts, not the 12-16mm that come with a cage.
- M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Icom IC-M502 / IC-M501EURO VHF marine radio, closest length match first.
- Wheelchair armrest and footrest brackets also M5 × 20 mm
- EcoFlow Power Kits Power Hub wall/RV mounting hardware also M5 × 20 mm
- E-scooter fenders & kickstands also M5 × 20 mm
- Rowing machine rail brackets also M5 × 20 mm
- Bike rack & fender eyelets also M5 × 20 mm
- Leviton EV Series charging pedestal (EPED1 / EPED2) also M5 × 20 mm
- Shelving brackets also M5 × 20 mm
- RV appliance and vent fan brackets also M5 × 20 mm
Questions about Icom IC-M502 / IC-M501EURO VHF marine radio screws
- What size screw does Icom IC-M502 / IC-M501EURO VHF marine radio use?
- M5 × 20 mm for mounting bracket uses the 2 supplied M5 x 20mm screws.
- How long are the screws in Icom IC-M502 / IC-M501EURO VHF marine radio?
- The record gives 20 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Icom IC-M502 / IC-M501EURO VHF marine radio?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.