Gas grill cart and legs screw size
M6 · 20 to 35 mm long
If you are replacing a screw on Gas grill cart and legs, the thread is M6 in lengths from 20 to 35 mm.
Where it is used: joins the cart side panels and legs.
This entry is marked reported and comes from webergrills.com.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Gas grill cart and legs screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 20–35 mm | 1 mm | not stated | not stated | joins the cart side panels and legs | Reported |
Fitment records and sources
joins the cart side panels and legs
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 20–35 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with Gas grill cart and legs, closest length match first.
- Car license plate U-clip retaining fasteners (trim) also M6 × 20 mm
- Exercise bike seat post clamp also M6 × 20–35 mm
- Heavy flat-pack furniture also M6 × 25–30 mm
- Car license plate mounting screws also M6 × 20 mm
- Motorcycle fairing panels also M6 × 20–25 mm
- Small boat deck hardware also M6 × 20–25 mm
- Bicycle disc caliper mount (post / IS) also M6 × 20–30 mm
- Suzuki V-Strom also M6 × 20 mm
Questions about Gas grill cart and legs screws
- What size screw does Gas grill cart and legs use?
- M6 × 20–35 mm for joins the cart side panels and legs.
- How long are the screws in Gas grill cart and legs?
- The records range from 20 to 35 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Gas grill cart and legs?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.