What size screw does Google Pixel 7 battery bracket use?

M1.4 × 2–3 mm for torx screws at the battery connector bracket.

How long are the screws in Google Pixel 7 battery bracket?

The records range from 2 to 3 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.4 screw?

0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.

What screwdriver do I need for Google Pixel 7 battery bracket?

The source lists a Torx drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.

Can I use an imperial screw instead of M1.4?

No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Google Pixel 7 battery bracket?

TechSpareWarehouse (our own store) lists M1.4 x 2mm, which matches the length in the records above.

Google Pixel 7 battery bracket screw size

M1.4 · 2 to 3 mm long

If you are replacing a screw on Google Pixel 7 battery bracket, the thread is M1.4 in lengths from 2 to 3 mm.

Where it is used: torx screws at the battery connector bracket.

Head and drive, as the source states them: Torx drive.

This entry is marked reported and comes from ifixit.com.

M1.4 means a 1.4 mm nominal diameter with a 0.3 mm thread pitch. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.

Google Pixel 7 battery bracket screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M1.4	2–3 mm	0.3 mm	not stated	Torx	Torx screws at the battery connector bracket	Reported

Fitment records and sources

M1.42-3mmreported

Torx screws at the battery connector bracket

pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3

Source

How to check the screw before you buy

Phone and wearable screws are tiny and often differ by fractions of a millimetre between positions; keep each one next to the hole it came from.
Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 2–3 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source names a Torx drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M1.4

M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Phones, Tablets & Wearables

Akuvox A08 video doorbell Akuvox A08 video doorbell (back plate)Anbernic RG35XX rear case screws Apple Watch case screws Apple Watch strap adapter ASUS ROG Ally (RC71L)Asus ROG Ally (RC71L) back panel and M.2 2230 SSD cover ASUS ROG Ally RC71L rear shell Compact smart sensor PCBs Dive watch bezel insert Dive watch bezels Extech 407732 sound level meter battery cover screw

Browse all 134 in Phones, Tablets & Wearables →

The same screw also fits

Devices whose records share a thread with Google Pixel 7 battery bracket, closest length match first.

OnePlus / Xiaomi flagship midframes also M1.4 × 2–3 mm
Samsung Galaxy A-series internal repair screw also M1.4 × 3 mm
Sennheiser MKH800 / SK6000 microphone/wireless products also M1.4 × 3 mm
Garmin smartwatch back cover also M1.4 × 2–3 mm
Nokia Lumia 1020 internal chassis screw also M1.4 × 3 mm
Samsung Galaxy S23 screen/battery assembly also M1.4 × 2–3 mm
Watch casebacks & dials also M1.4 × 2–3 mm
Samsung Galaxy S23 USB-C daughterboard also M1.4 × 2–3 mm

Questions about Google Pixel 7 battery bracket screws

What size screw does Google Pixel 7 battery bracket use?: M1.4 × 2–3 mm for torx screws at the battery connector bracket.
How long are the screws in Google Pixel 7 battery bracket?: The records range from 2 to 3 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M1.4 screw?: 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
What screwdriver do I need for Google Pixel 7 battery bracket?: The source lists a Torx drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
Can I use an imperial screw instead of M1.4?: No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Google Pixel 7 battery bracket?: TechSpareWarehouse (our own store) lists M1.4 x 2mm, which matches the length in the records above.

Heads up: shipping delay