Google Pixel 7 rear camera bracket screw size
M1.4 · 2 mm long
Google Pixel 7 rear camera bracket takes M1.4 metric screws, 2 mm long.
The record covers torx screws holding the rear camera module.
Head and drive, as the source states them: Torx drive.
This entry is marked reported and comes from ifixit.com.
An M1.4 screw is 1.4 mm in diameter with a 0.3 mm pitch, tapped with a 1.1 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Google Pixel 7 rear camera bracket screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 2 mm | 0.3 mm | not stated | Torx | Torx screws holding the rear camera module | Reported |
Fitment records and sources
Torx screws holding the rear camera module
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Over-long screws in phones are a known cause of damaged boards (Apple's 'long screw damage'), so never swap positions.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 2 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Torx drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Phones, Tablets & Wearables
The same screw also fits
Devices whose records share a thread with Google Pixel 7 rear camera bracket, closest length match first.
- Fitbit / fitness band back cover also M1.4 × 2 mm
- Miniature precision instrument screws (NBK) also M1.4 × 2 mm
- Google Pixel 7 motherboard also M1.4 × 2 mm
- Samsung Galaxy Z Fold hinge and board also M1.4 × 2 mm
- Samsung Galaxy S23+ internal shields also M1.4 × 2 mm
- Apple Watch case screws also M1.4 × 2 mm
- Samsung Galaxy S23 board screws also M1.4 × 2 mm
- Samsung Galaxy S23 USB-C daughterboard also M1.4 × 2 mm
Questions about Google Pixel 7 rear camera bracket screws
- What size screw does Google Pixel 7 rear camera bracket use?
- M1.4 × 2 mm for torx screws holding the rear camera module.
- How long are the screws in Google Pixel 7 rear camera bracket?
- The record gives 2 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Google Pixel 7 rear camera bracket?
- The source lists a Torx drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Google Pixel 7 rear camera bracket?
- TechSpareWarehouse (our own store) lists M1.4 x 2mm, which matches the length in the records above.