Gravity A 38F M6M mic-stand adapter screw size
M6 · length not stated in the sources
Our records put Gravity A 38F M6M mic-stand adapter on M6 screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for 3/8-inch female to M6 male adapter for mounting M6-threaded clips and brackets on mic stands.
This entry is marked confirmed and comes from gravitystands.com.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Gravity A 38F M6M mic-stand adapter screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | not stated | 1 mm | not stated | not stated | 3/8-inch female to M6 male adapter for mounting M6-threaded clips and brackets on mic stands | Confirmed |
Fitment records and sources
3/8-inch female to M6 male adapter for mounting M6-threaded clips and brackets on mic stands
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Mic stand threads (5/8-27) and tripod threads (1/4-20, 3/8-16) are imperial, not metric — only accessory clips like Gravity's M6 adapter are genuinely M6.
- UR cobot flange bolts are commonly sold/quoted as 'M6 bolts' but the required length depends on the tool thickness; UR's own guidance is bolt class M6-8.8 to ISO4762 without a fixed length, so length must be selected per adapter/tool stack-up, not assumed as a fixed mm value.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Gravity A 38F M6M mic-stand adapter, closest length match first.
- Weidmuller WDU 70/95 and WDU 120/150 terminal blocks also M6
- cab Applicator A3200 print-and-apply labeling system (packaging line hardware) also M6
- EIA-310 square-hole equipment racks (Hammond CAGKIT-M6) also M6
- Fluke Y2638 rack-mount kit (2638A data acquisition) also M6
- Rittal SZ 4182.000 mounting bracket PS also M6
- Panduit NetManager horizontal cable manager mounting screw also M6
- Weidmueller ZB 35 busbar terminal blocks / DIN-rail busbar system also M6
- Rack audio flight case rails also M6
Questions about Gravity A 38F M6M mic-stand adapter screws
- What size screw does Gravity A 38F M6M mic-stand adapter use?
- M6 for 3/8-inch female to M6 male adapter for mounting M6-threaded clips and brackets on mic stands.
- How long are the screws in Gravity A 38F M6M mic-stand adapter?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Gravity A 38F M6M mic-stand adapter?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.