Panduit NetManager horizontal cable manager mounting screw screw size
M6 · length not stated in the sources
Panduit NetManager horizontal cable manager mounting screw takes M6 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for legacy spec - M6 option discontinued in a 2021 change notice.
This entry is marked confirmed and comes from file.icallin.com.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Panduit NetManager horizontal cable manager mounting screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | not stated | 1 mm | not stated | not stated | Legacy spec - M6 option discontinued in a 2021 change notice | Confirmed |
Fitment records and sources
Legacy spec - M6 option discontinued in a 2021 change notice
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Rack hole threads vary: 10-32 and 12-24 are still common in US racks alongside M6 - check the rail before buying.
- 19-inch racks are not all metric: 10-32 and 12-24 UNC are still the norm in North America, with M6 the metric/square-hole cage-nut option.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Panduit NetManager horizontal cable manager mounting screw, closest length match first.
- Weidmueller ZB 35 busbar terminal blocks / DIN-rail busbar system also M6
- Rittal SZ 4182.000 mounting bracket PS also M6
- Tektronix RM5 rackmount kit (5/6 Series MSO) also M6
- PCB Piezotronics IMI M624B01 (bolt M081A67) Ring-style ICP accelerometer stud mount for heavy/off-highway equipment also M6
- S:FLEX Hanger Bolt / Solar Fastener System also M6
- RF Elements Twin Horn antenna bracket also M6
- FJD 3D Excavator Guidance System (GNSS/IMU hardware) also M6
- Rack audio flight case rails also M6
Questions about Panduit NetManager horizontal cable manager mounting screw screws
- What size screw does Panduit NetManager horizontal cable manager mounting screw use?
- M6 for legacy spec - M6 option discontinued in a 2021 change notice.
- How long are the screws in Panduit NetManager horizontal cable manager mounting screw?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Panduit NetManager horizontal cable manager mounting screw?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.