HARTING D-Sub jackscrew 09670019992 screw size
M2.5 · length not stated in the sources
HARTING D-Sub jackscrew 09670019992 takes M2.5 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: D-Sub connector panel jackscrew.
This entry is marked confirmed and comes from HARTING datasheet 09670019992.
M2.5 means a 2.5 mm nominal diameter with a 0.45 mm thread pitch. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.
HARTING D-Sub jackscrew 09670019992 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2.5 | not stated | 0.45 mm | not stated | not stated | D-Sub connector panel jackscrew | Confirmed |
Fitment records and sources
D-Sub connector panel jackscrew
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
Source: HARTING datasheet 09670019992
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2.5
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with HARTING D-Sub jackscrew 09670019992, closest length match first.
- PW-Sat2 CubeSat secondary structure and panels also M2.5
- HP Pavilion also M2.5
- nVent SCHROFF instrument/enclosure collar panhead screw also M2.5
- CubeSat exterior panel corner bracket countersunk screw also M2.5
- HP EliteBook 840 G2 / 740 G2 / ZBook 14 G2 also M2.5
- NVG shroud / helmet bracket hardware (Gentex-style 3-hole) also M2.5
- HP EliteBook 725 G3 also M2.5
- Keystone Electronics metric nylon standoff also M2.5
Questions about HARTING D-Sub jackscrew 09670019992 screws
- What size screw does HARTING D-Sub jackscrew 09670019992 use?
- M2.5 for D-Sub connector panel jackscrew.
- How long are the screws in HARTING D-Sub jackscrew 09670019992?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M2.5 screw?
- 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
- What screwdriver do I need for HARTING D-Sub jackscrew 09670019992?
- The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
- Can I use an imperial screw instead of M2.5?
- No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.