Honeywell Vuquest 3310g barcode scanner screw size
M3 · length not stated in the sources
Our records put Honeywell Vuquest 3310g barcode scanner on M3 screws. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: three M3 x 0.5 threaded inserts on scanner base for stand/bracket mounting.
This entry is marked confirmed and comes from sps-support.honeywell.com.
An M3 screw is 3 mm in diameter with a 0.5 mm pitch, tapped with a 2.5 mm drill; imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Honeywell Vuquest 3310g barcode scanner screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | not stated | 0.5 mm | not stated | not stated | Three M3 x 0.5 threaded inserts on scanner base for stand/bracket mounting | Confirmed |
Fitment records and sources
Three M3 x 0.5 threaded inserts on scanner base for stand/bracket mounting
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.
More in Electronics, Racks & Enclosures
The same screw also fits
Devices whose records share a thread with Honeywell Vuquest 3310g barcode scanner, closest length match first.
- Hammond 1555F enclosure also M3
- Instrument enclosure base/rear panel screws (Metcase Technomet-Control rack case) also M3
- Eurorack synthesiser case (Intellijel 7U Performance Case Gen 2) also M3
- Ubiquiti UniFi AP / UAP-LR ceiling & wall mount kit also M3
- Ubiquiti UniFi UAP-AC access point also M3
- Southco polished spring-ejected captive panel fasteners also M3
- External 3.5in HDD enclosures also M3
- NVG bracket mount screw set (tactical helmet) also M3
Questions about Honeywell Vuquest 3310g barcode scanner screws
- What size screw does Honeywell Vuquest 3310g barcode scanner use?
- M3 for three M3 x 0.5 threaded inserts on scanner base for stand/bracket mounting.
- How long are the screws in Honeywell Vuquest 3310g barcode scanner?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Honeywell Vuquest 3310g barcode scanner?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.