HP 15-ed1000 (ids 32552495 screw size

HP 15-ed1000 (ids 32552495 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2.4–6.6 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M1.6 heads take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP 15-ed1000 (ids 32552495, closest length match first.

• Lenovo ThinkPad P14s Gen 3 also M2 × 3.5 mm
• Lenovo ideapad 320SX-14IKB also M2 × 3.5 mm
• Lenovo ThinkPad T61p (14.1-inch) also M2 × 3.5 mm
• HP ENVY 17-cg1000 (ids 32552529 also M1.6 × 2.5 mm
• HP 256 G3 also M2 × 3.5 mm
• Dell XPS 13 9310 also M1.6 × 2.5 mm
• Dell Inspiron 13 7300 2-in-1 also M2 × 3.5 mm
• Lenovo Flex 4-1570 also M2 × 3.5 mm

Questions about HP 15-ed1000 (ids 32552495 screws

What size screw does HP 15-ed1000 (ids 32552495 use?

M1.6 × 2.5 mm for touchpad (qty 3, broadhead, Phillips); M2 × 2.4 mm for system board (qty 6, broadhead, Phillips); M2 × 2.7 mm for base cover (qty 6, Torx T5); M2 × 3.5 mm for SSD (qty 1, Phillips); M2 × 3.5 mm for unspecified (qty 1, Phillips); M2 × 3.5 mm for wireless card (qty 1, Phillips); M2 × 4.1 mm for battery (qty 6, Phillips); M2 × 4.1 mm for fan (qty 2, Phillips); M2 × 4.1 mm for heat sink (qty 4, Phillips); M2 × 4.1 mm for hinge (qty 2, Phillips); M2 × 4.1 mm for SSD (qty 1, Phillips); M2 × 4.1 mm for system board (qty 4, broadhead, Phillips); M2 × 4.2 mm for speaker (qty 4, broadhead, Phillips); M2 × 6.6 mm for base cover (qty 6, Torx T5); M2.5 × 2.9 mm for hinge (qty 6, Phillip.

How long are the screws in HP 15-ed1000 (ids 32552495?

The records range from 2.4 to 6.6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.6 screw?

0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.

What screwdriver do I need for HP 15-ed1000 (ids 32552495?

The source lists a Phillips and Torx T5 drive. Standard M1.6 heads otherwise take PH00 (Phillips) or T4–T5 (Torx), or a 1.5 mm hex key.

Can I use an imperial screw instead of M1.6?

No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP 15-ed1000 (ids 32552495?

TechSpareWarehouse (our own store) lists M2 x 2.5mm, M2 x 4mm and M2.5 x 3mm, which match lengths in the records above.